EZ CAR CRUSHER MODEL B With Remote --HydraulicsSystem Pressure 2500 psiPort Reliefs Set At 2650 psi --Cylinders 8" bore --Travel 72" --Shaft 2.5" rod --OpeningSize 20" x 7'6" x 7'7" --OverallWeight 49,000 lbsLength 43'5"Travel & Operating Height 13'3"

EZ SANDER EZ-3760 Wide Belt SanderEZ-Sander's are built to with the ability to hold very tight tolerance (+/-.003) side to side when set up properly.Specifications: -- The sanding head is a combination head that consists of a 5" rubber-covered contact drum for the more aggressive sanding and then followed by an adjustable 2-1/2" graphite-covered felt polishing platen for doing very fine finishing sanding using a 37" X 60" abrasive belt. -- The conveyor belt speed is set to run at 10 - 30 FPM and is controlled via AC variable speed unit mounted in the main control panel. Simply adjust the dial setting to your desired feed speed. -- Double infeed and outfeed hold-down rolls are provided to help ensure proper part feeding through the Sander. -- The conveyor table/bed opening has a 0" to 5" opening allowing the operator to sand some parts as thick as 5" and the ability to sand very thin parts as well. -- Power raising and lowering of the conveyor bed is standard. -- Digital thickness display is standard.Complete with & Features: -- EZ Sander is equipped with a state-of-the-art electronic tracking system for the abrasive belt. -- Emergency stop heavy-duty caliper disc brakes bring the sanding head to a stop within 4 to 5 Sec when activated by the machine's safety interlock system. -- Limit Switches on both sides of the abrasive belt to keep the belt from over-travel. NOTE: -- Available in single phase with a 7.5 HP or 10 HP 3-Phase main drive motor. -- Voltage change to 440 Volt ...$275.

The Fanuc M-410iC/110 robot is a palletizing robots. It runs on the Fanuc R30iB and R30iB Plus controller platform. With lighter payload this robot is designed to run faster than its bigger variants.This robot was ordered and never installed, so it is new old stock.Maximum Payload 110 kg (242 Lb.) --Reach 2,403 mm (94") --4 Axes --Repeatability +- 0.5 mm --Robot Mass 1030 Kg (2270 lbs) --Floor Mounted

FANUC M410/160 iB ROBOT PALLETIZING SYSTEM Specifications: -- Complete with R-30iA Controller All Refurbished -- Pillow Bag Tooling -- 4-Axis control -- Mounted to a heavy-duty base -- 10 Feet Long Rubber Belt Conveyor -- (2) 5 Feet Motorized Pallet Conveyor -- (3) 10 Feet Motorized Pallet Conveyor -- Automatic Pallet Dispenser -- up to (14) 50 Lbs bags per minute -- Machine weight 4500 LbsAUTOMATIC PALLET STRETCH WRAPPING SYSTEMWULFTEC or LANTECH Stretch Wrapping System or Equivalent Not INCLUDED

FANUC ROBOT S430iWFANUC Robot for palletizing rectangular compressed bags.Specifications: -- (6) Axes. -- Payload 165 kG (255 Lbs). -- H-reach 2643 mm (104"). -- Robot mass 1300 kG (2,860 Lbs). -- Complete with pendant control. -- Complete with Gripper type arm and pallet gripper. -- Refurbished with 90 days Warranty. -- Buyer to install safety guards.Note: Machine has been rebuilt is 2021

COMPLETE FANUC 125I ROBOTIC PALLETIZING SYSTEM --System Includes the following: --FANUC M-410IB/160 Palletizing Robot with Controller and Stand --Robot will be tested --End of Arm Tooling to Pick, Fork Style, Picking 94 Lbs Concrete Bags --Master System Control Panel, 480 VAC 3PH & 24VDC Controls with HMI --Allen-Bradley Light Curtain with Safety Controller --Infeed Chain Drive Roller Conveyor 10 Feet --Pallet Hopper --Safety Fencing COST --20 Feet Exit CDLR Pallet Conveyor 52" Wide --System Integration / Programming

FANUC 165 Complete Palletizing SystemEquipped with and includes: -- FANUC 165 Complete with R-2000iA Controller with 600mm stand -- Pick-Up Arm Gripper Arm for pillow bag type -- 5 Feet x 24" Motorized In-feed Belt Conveyor -- (1) 10' Motorized Pallet Conveyor -- Automatic Pallet Dispenser -- Price includes Loading on your Truck

END ARM TOOLING FOR FANUC ROBOT -- Gripper Finger Type End Arm Tooling -- Design for Fanuc Robot Model S-430iW -- Loaded on your truck

Large table size, extendable in all three directions by up to 39" (1,000 mm) without the requirement of tools. Comfortable one-handed lever operationHeavy-duty eccentric clamp, usable on the left and right-hand side.Specifications: -- 3 HP motor, tilting head, manual hand lever control for mortise length and depth; 13" x 22" table with eccentric clamp -- 3000 RPM, reversible motor that caters for left and right cutting bits and a solid quad-jaw chuck with clamping range from 0–20 mm -- Lateral range of motion is 250 mm, cut depth is 160 mm, available height adjustment is 130 mm and there are solid locking stops in all three directions for setting precise stops.Features: 2-Jaw chuck with 5/8" capacity, Dust control collection tray below the cutter out to an 80 mm outlet,Complete with (2) adjustable and removable extension wings; fence for 90° & 45° mortises, extended stop bar on each side of table.

FELDER FORMAT 4 - C-EXPRESS 920 CNC MACHINING CENTER (FEED THRU W/ROUTING): -- Specifications: Automatic CNC Feed Through Point to Point Boring Machine that combines flexibility and high productivity.A perfectly suited solution for small to midsize companies & artisans in need of an automatic solution for precision drilling with a low cost investment.Parts can be discharged at the opposite end of the machine for automated material handling or returned to the Operator for manual unloading. -- Working Field:Max. panel size on X-Axis 118" (3,000 mm); Y-axis is 36.2" (920 mm); Z-axis is 2" (50 mm).Min. panel on size X-axis is 11" (280 mm); Y-axis is 7.1" (180 mm); Z-axis is 0.4" (10 mm).Max. Panel weight 66 Lbs (30 kG). -- Positioning Speed: Panel feeding speed of 229 FPM (70 MPM), Y-axis at 229 FPM (70 MPM), Z-axis at 65 FPM (20 MPM).Axes positioning by AC drives & brushless Servo motors; the Panel moves in X-axis & the boring head moves in Y- & Z-axes. -- Work Area:NC Controlled "Optical Laser Sensor" creates a zero-panel reference point by reading the panel's ends; this ensures that RH & LH (mirror image) panels will always be symmetrical.High precision clamping automatically positions the workpiece. Automatic presser moves independently and adjusts to workpiece thickness. Pneumatic side pusher makes locating workpiece accurate and efficient. LH Side pressure clamp with automatic adjustment & pneumatic locking according to the panel width.Scratch resistant rollerball table makes for ease of loading parts into the machine. -- Boring Unit:3 HP (2.2 kW) Motor, variable speed from 4,500 - 8,000 RPM.(9) Independent vertical spindles on 32 mm centers: (5) Spindles in X-axis & (4) spindles in Y-axis.(6) Horizontal spindles with: (2 + 2) in X-Axis & (1 + 1) in Y-axis.(1) X-Axis grooving saw for max. 120 mm dia. blade, variable speed from 5,500 - 10,000 RPM. -- Machining:5 HP (3.7 kW) Motor, variable speed from 1,000 - 18,000 RPM with ER 32 adaptor & manual tool change system. -- Operator & Machine Control: PC-Based user-friendly icon driven Control housed on the main machine base + "WOODFLASH" Operating System. 19' LCD Displays programming graphics, functions, machine data. -- Complete with: User & Maintenance Manuals; handheld pendant. -- Options Include: &#9679 Special side clamping device for min. panel size in Y-axis of 2-3/4" (70 mm). &#9679 Additional retractable infeed support table with roller balls. -- Actual model is: FELDER FORMAT 4 - C-EXPRESS 920 CLASSIC

FELDER FORMAT 4 TEMPORA F400 45.03 EDGEBANDER (W/PRE-MILL) + EVA/PUR GLUING TECHNOLOGY: -- Specifications:Working Capacity:Min. workpiece width: 70 mm; min. workpiece length: 140 mm; min. workpiece height: 8 mm; max. workpiece height: 45 mm; edge thickness in coils (min./max.) 0.4 - 3 mm.Features & Equipped with: "M-motion" SmartTouch Control with: 10.4" Touchscreen display with integrated maintenance software and network connection. -- Solid steel machine chassis. -- Pullout workpiece support to assist in the processing of larger work-pieces. -- Motor-driven adjustment of the top pressure beam with (2) offset lines of rollers for equal pressure distribution on the workpiece. -- Chain feeder with a speed of 9 MPM (30 FPM) and rubber grip pads for maximum grip on the workpiece. -- 770 mm Diameter workpiece support roller; running on ball bearings. -- Feeding guide with rollers for processing fragile material.Working Units: Pre-milling unit with: (2) 1.1 kW Independent motors running at 12,000 RPM and diamond-tipped cutters; motor-driven positioning of the depth of cut between 0 – 2 mm; (2) diamond-tipped cutters included (Dia. = 80 mm, H = 49 mm, Z = 2+2). -- Edge feed for coiled material: 0.4 – 3 mm Thick coil stock, with edge presence recognition via an infrared sensor. -- Guillotine trimming unit for: Precutting of PVC/ABS edge band material 0.4 – 3.0 mm thick. Teflon coated gluepot with: (10) Minute heat up time; 1.5 kG capacity. - Glue is applied using a fine adjustable glue roller and quick-change System, as well as monitoring of the heating cartridge; pneumatically feed controlled glue unit capable of processing EVA and PUR hot-melt glue. Motor-driven positioning of the pressure unit with: (1) Large motor-driven roller and (1) conical roller operating pneumatically. -- End trimming unit with: (1) Motor, 0.35 kW and 12,000 RPM. -- Multi-functional trimming unit for: Radius & flush trimming and bevel trimming of thin edges with (2) independent motors, each with 0.75 kW and 12,000 RPM; manual positioning of the edge thickness adjustment with pneumatic disengage function via the Control Panel. -- Finishing Units with: 0° - 10° Manual adjustment. -- Complete with: Cleaning & Release Sprayers; T & B Buffing units. -- Actual Model is: FELDER FORMAT 4 TEMPORA F400 45.03.

FELDER G-330 EDGEBANDER0.4 - 3 mm Edge thickness cap. and 40 mm panel thickness; 3" min. width and 4-3/4" min. panel length.Equipped with: -- Quick Melt Teflon coated glue pot for granular hot-melt adhesive. -- Heavy Duty guillotine for up to 3 mm thick PVC. -- Integrated Operator PLC controls and an LCD display. -- "Anti-slip" rubberized surface chain pads.Workstations: -- Single motor, Double Blade End Trim with HF motor - 12,000 RPM. -- Top & Bottom Flush/Bevel Trim, bevels 0° - 15° (0.5 HP motor - 12,000 RPM each). -- Open space at out feed . -- Single feed speed of 26 FPM.Complete with: -- Sound & Safety enclosure over trim stations and outrigger panel support, and used tooling.NOTE: Seller states that the equipment has less than 500 hours of use!

This FISHER + RUCKLE is actually called a "FISHER + RUCKLE/MONGUZZI ADF76-2800" Double-Knife Veneer Guillotine.110" (2,800 mm) Max. knife length, double-knife guillotine; motorized front knife adjustment.Specifications: -- 3/8" - 20-3/8" (9.5 - 517 mm) Adjustment; 3-15/16" (100 mm) max. daylight opening. -- Microprocessor controlled knife opening with: Keypad entry & LCD readout. --Rear fence with auto-trim cut feature, slow & fast fence movement. -- Hydraulic pressure beam & knives can be activated separately & together. -- Hydraulic system with: 10 HP (7.5 kW) Pump and reservoir for knives & pressure beam activation. Complete with: -- Installed knives and Light beam Infrared safety zone.Actual model ix AFD 76-2800 &#9679 . OEM, Monguzzi model is TRM-2L. Exactly the same machine.

FLETCHER FM-2000 Contour EdgebanderSpecifications: 0.4 mm to 2 mm Banding thickness, up to 2" panel thickness, Unit to run strip veneer, coil, rolls of PVC, melamine, or wood veneer. Large overhead glue pot with a quick heat time of 10 minutes. Equipped with: -- Programmable temperature control with safety interlock so that applicator does not run until proper operating temperature is reached. -- 1-3/4" silicone-coated drive roll. -- Foot pedal-controlled tape advance. -- Foot pedal emergency stop. Optional Equipment: -- Power-Feed $ 2,618.00 -- 3° Manual Tilting Table $ 809.00 -- 45° Tilting Table $ 5,382.00 -- Push Button Powered Operated Tilt Table $ 6,232.00 -- Outboard Stock Support $ 1,565.00 -- 3MM Capable $ 2,950.00 -- 4"; Thickness Capacity $ 10,000.00

FLETCHER EZ-DOOR Raised Panel Door MachineThis freestanding machine can produce an entire 5-piece door in a matter of minutes. Easy to operate, the E-Z Door has a 4-position configuration to produce raised panels, cope/stile profiles and mullions for glass doors. Cathedral doors are produced by using a quick change template system.Specifications: -- Select cutter and material stop with the press of one button. -- Simple four position one spindle design. -- PLC controlled pneumatics. -- Rigid lubricated spindle assembly. -- Re-circulating ball bearing slides. -- 10 HP 230 or 460V/60HZ spindle motor – (460V/3PH=17FLA) – (230V/3PH=33FLA) -- 6,500 RPM spindle speed. -- 62 inch travel length standard with circulating ball bearing slides, cut rails to 59"; and panels to 55"; -- Includes: (4) Standard cutters (shape to be decided), others optional. -- Includes: one template of customers choice. -- 1-¼"; Arbor. -- CFM requirement is 392.Made in North Carolina, USA!

FLETCHER/DELMAC - DMG-50CB, ...Contour EdgebanderSpecifications -- Overall table size: 18" x 48"; x 39-1/4"; H; 18" x 48"; Tilting section with: 0° - 15° Tilt.Equipped with: -- 20" Dia. Coil table. -- Guillotine. -- Glue Pot & Roller. -- DELMAC Thermo-Regulator Control with: (2) WATLOW "Series 965" Digital temperature controllers; LED display & touchpad for Glue pot & roller; LCD band length counter. -- Dual foot pedal controls.

FLEX-KLEEN 43/54 PSTL 225 III Pulse Jet Dust Collector. -- General Data: 36,000 ACFM (approx.) based on 3.73 to 1 Air-to-Cloth Ratio; Square baghouse design with (225) Rigid Pleated Polyester Filter Media. approx. 9,675 sq. feet of filter area, Cartridges are 54" high and 43 sq. of filter area, each. High entry inlet designed for about 20" WG of Static Pressure. -- Filter Cleaning: Plant compressed air supplied to manifold and diaphragm valves periodically supplies pulse jets to filter bags according to a controller. -- Discharge: Small 8"x8" RAL - Rotary Air Lock (was used on paper dust). -- Construction: V-shaped collection hopper discharges into a sealed RAL. -- Overall dimensions: TBA -- Actual model: 43/54 PSTL-225, Arrangement III. -- No Fan or Cyclone are included.

FLEXICON HOPPER/FEEDERSpecifications: -- Flexible Screw Approximately 12 Feet -- 7" Diameter -- Flights 6-1/2" -- Tube Diameter 7-1/2" -- Discharge Height 86 Inches -- Discharge Diameter 10 Inches -- 10 HP Motor -- Dimensions; 72" Long x 48" Height x 7-1/2" Depth -- Loaded on your Truck

FLOW AIRE - DC-03, ...Cartridge Dust CollectorSpecifications: -- Holds (16) cartridge filters. -- Includes: New AirMax Premium Media Cartridge Filters - fire retardant. -- Total dilter media area: 3,616 sq/ft. -- Air-to-Media ratio @ 8,000 CFM: 2.21:1. -- Automatic Pulse Clean System with: Differential pressure gauge and sequencing control in enclosure. --Single Hopper outlet with Sealing Drum Cover Kit. -- Steel support structure. -- Includes: 20 HP Ground mount blower. -- Rated for :8,000 CFM. -- Motor starter & controls.Sold with a 6-Month Mechanical Warranty

FOLEY - 367, ...Saw Blade SharpenerDesigned expressly for carbide-tipped saw blade grinding, with 0.5 HP motor. -- Performs all (3) required operations: Face grinding, top grinding, and side grinding with speed efficiency. -- 4" - 40" Dia. saw blade cap., carriage travel: 5-1/2", cross-feed travel of 8-3/4". -- Calibrated indicators ensure blade roundness and equal tooth heights.