TWIN FLOW Air Make-Up Unit 7,000 CFM. Vertical mount with Remote Control Panel: -- CFM: 7,000 CFM @ 1.75" ESP, 5HP/575v/3ph/60Hz TEFC motor -- BTU: 0.68 MBTUH -- Burner: MAXON burner -- Temperature Control: 80º F temperature rise in spray cycle -- Mounting: Vertical, outdoor/indoor mounted -- Fuel required: Natural gas, 0.3 PSI pressure -- Intake/Discharge: Vertical, screened, air intake with vertical discharge -- Filter Sections: V-Bank style with 1’’ cleanable air intake disposable type filters -- Gas Control: Control cabinet and pre-piped gas combustion system mounted on burner section to FM, Electronic Modulation -- Specifications includes: Digital Temperature Controller, ON/OFF & Summer/Winter Switch, pressure regulator, metering valve, pilot pressure regulator & pilot gas valve, flame rod, high limit switch, air flow switch, power transformer, ignition transformer and spark plug -- Electrical Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Motor Control: Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Enclosure Design: Framed, with 18 ga. metal walls and 1" insulation -- Note: Available in Horizontal and Vertical mount. Please inquire.

TWIN FLOW Air Make-Up Unit 14,000 CFM. Vertical mount with Remote Control Panel: -- CFM: 14,000 CFM @ 1.75" ESP, 10 HPTEFC motor -- BTU: 1.38 MBTUH -- Burner: MAXON burner -- Temperature Control: 80º F temperature rise in spray cycle -- -- Mounting: Vertical, outdoor/indoor mounted -- Fuel required: Natural gas, 0.3 PSI pressure -- Intake/Discharge: Vertical, screened, air intake with vertical discharge -- Filter Sections: V-Bank style with 1’’ cleanable air intake disposable type filters -- Gas Control: Control cabinet and pre-piped gas combustion system mounted on burner section to FM, Electronic Modulation -- Specifications includes: Digital Temperature Controller, ON/OFF & Summer/Winter Switch, pressure regulator, metering valve, pilot pressure regulator & pilot gas valve, flame rod, high limit switch, air flow switch, power transformer, ignition transformer and spark plug -- Electrical Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Enclosure Design: Framed, with 18 ga. metal walls and 1" insulation -- Note: Available in Horizontal and Vertical mount. Please inquire. -- Also available: Controls option: - Two stages for 14,000 or 7,000 CFM at extra cost of about $3,000.

TYLER 804 Air Pod Press; Overall Platen dimension of 50" x 100", with (4) individually controlled top platens - each 25" X 50". -- Side loading on 100" side. -- 0 - 50" Motorized adjustable daylight. -- Pneumatic top pressure via 5-1/2" stroke air pods by (32) 8" Air Pods with maximum 50 PSI specific pressure. -- Spring loaded rollers in bottom platen for easy loading & unloading of stack.Overall Dimensions - 122" Long x 60" Wide x 97" High

TYLER 2400 SLOT-WALL MACHINE: -- Specifications:Produces T-slot "slat-wall" for architectural/store fixtures. 4' x 8' (48" x 97") max. panel cap., 2' x 2' (24" x 24") min. panel cap., min. panel thickness = 0.5" max. panel thickness = 1.5"; The Tyler 2400 can machine up to (40) panels/Hr, depending on material density, thickness and the slot profile. -- Equipped with: (18) Router spindles all on 3" fixed centers, spindles are driven in groups of (3) with (6) 7.5 HP - 3,450 RPM motors, all router spindles rotate @ 15,400 RPM. -- Operation: Panels remain stationary on top, pneumatically clamped in place while the bottom mounted router bank traverses the full length of the panel with a high-speed return, variable feed speed control, router assembly traverses on ground & polished rails with chain drive. -- Panels are positioned along the 8' rear edge fence line, distance from the panel edge to the centerline of the 1st cut can be adjusted from 0.0" - 3" (1 router spindle pitch). -- Overhead hold-down assembly with (2) large air cylinders and (5) arms with spring loaded clamping pads hold the panel in place. Panels are loaded from the 8' front and exit to the side. -- Includes: Operator controls for the machine cycle and a "setup" mode of operation; machine cutting cycle is initiated by a 2-hand operator safety buttons located on the right front of machine. - Produces approx. (30 - 40) panels per hour. -- Available Options at Additional Cost:Router spindles on 4'- & 100-mm centers; 48" x 121" workpiece capacity increases left-to-right workpiece (length) capacity.60" x 97" workpiece capacity increases front-to-back workpiece (width) capacity & includes (1) additional multi-spindle router head.60" x 121" workpiece capacity increases front-to-back & left-to-right workpiece capacity & includes (1) additional multi-spindle router head.

TYLER "POWER POD" Cold Press with Motorized OpeningThis TYLER "Power Pod" Press has a 36″ X 148″ capacity, side loading on 148" -- It consists of (3) individual top mounted platens with their own controls that measure 36"; wide x 49"; long each. There are a total of (27) total air pods or (9) for each platen. -- 3-1/2″- 48″ adjustable motorized daylight opening. -- The bottom platen has spring loaded rollers for easy loading and unloading. -- Max. operating pressure is 100PSI.NEW plumbing, NEW regulator, a few NEW air bags, NEW top plates, and fully cleaned and tested.

UAS FJH8-2 DUST HOG Cartridge Dust Collector with Rotary Air Lock. Approx. 3,500 CFM Cartridge Filter System, complete with capacity of 1,808 sq. ft. of filter area composed of (8) cylindrical cartridges (226 sq. ft. cloth area per cartridge), CFM based on a target 2:1 Air to Cloth Ratio.. -- Automatic Pulse Clean System with differential pressure gauge and sequencing timer board in enclosure. Continuous pulse jet cleaning via compressed air, (1) pulse valve per (2) cartridges. -- Includes: Bottom hopper ROTOLOK 8" Rotary Air Lock (not mounted and to be adapted). steel support legs. -- Features: Heavy Duty steel legs which can be extended for position a storage container below RAL's. -- Comes with: CINCINNATI 150 BI t0 HP side mounted direct drive fan motor which pulls dust laden air thru the collector (clean air side); Baghouse has dusty air inlet at the top of hopper and clean air discharge from fan. -- Price includes dismantling and loading on flatbed truck.

ULTRA GL-630H Feed Through Moulder: 6-Head (B-T-R/L-T-B), "Flooring" working capacity of 12" x 6".Specifications: -- Head sequence: Bottom 25 HP, top 30 HP, right 20 HP/left 20 HP (opposing), top 25 HP, and bottom 25 HP motor. -- Spindle dia. of 1-13/16" with cutterhead speed of 6,000 RPM; all spindles with high prevision bearings. -- Auto. positioning of the left & top spindles radially; all additional spindles with digital readouts, including chipbreaker & pressure elements. -- Pneumatics on all chipbreakers, pressure elements, and holddown rollers. -- Horizontal spindles with HydroLock outboard bearings on #1, #2, #5 & #6. -- Straight jointer on spindles #5 & #6; Profile Jointers on spindles #3, #4, #5 & #6. Equipped with: -- Inverter controlled feed drive, variable speed of 26 - 260 FPM. -- Infeed table 1.2 M (4') with all table plates & fences hard chromed to RC 70. -- Machine table includes: (5) Table rollers for smooth through feed; short stick attachment for through feed on pieces down to 230 mm. -- Electrical cabinet & pedestal for machine controls separate from machine, Heavy Duty sound enclosure. -- Includes Startup training and Warranty!

UMP BP 450 A 450 kg/hr. Briquette PressSpecifications: -- Cap. 450 kg/hr. (992 Lbs.). -- Max. pressure 1,700 kg/cm³ (24,175 PSI). -- Max. chip moisture content 15%. -- Max. chip size 15 mm (0.59"). -- Wood shaving to briquette ratio 10 to 1 (using mahogany). -- Briquette configuration: Rectangular. -- Briquette length 40 - 105 mm (1.57" - 4.13"), Briquette width 150 mm (5.91"), Briquette height 60 mm (2.36"). -- Briquette heat energy 4,200 kcal/kg (7,558 BTU/Lbs.). -- Hopper size 31"; x 36"; x 36";, with 1 side sloping so cutaway from cube of 18"; x 36";, Mounting flange at top allows additional capacity to be added).Equipped with: -- Automatic material density adjustment. -- Automatic hopper shutoff. -- SIEMENS PLC Control.

WYSONG & MILES 604 DOUBLE SIDED OSCILLATING EDGE SANDERDouble Sided Oscilating Edge Sander with 7.5 HP - 1,800 RPM TEFC motor; (2) 11" x 60" cast iron platens; 10" x 172" abrasive belt size, (150) oscillations/Min with 1/2" movement, 0.5 HP oscillation motor.Equipped with: -- (2) 11-1/2" x 62" Cast iron side tables and (1) cast iron end table; tables tilt 30° up & 45° down; 5" vertical table travel w/hand wheel adjustment, 5" lateral side table travel w/hand wheel adjustment, 4-1/2" lateral end table travel w/handwheel adjustment. -- 10" Dia. x 10-1/2" face direct drive pulley, 4-1/2" dia. x 10-1/2" idle pulley. Complete with: -- Magnetic controls with overload protection & dust hood with 4" dia. outlet.

WYSONG & MILES - 291, ...Stroke Sander (Manual)5 HP - 1,200 RPM Motor; roller table size: 32" x 84"; horizontal travel stroke: 38"; adjustable height of table base from 26" to 35" via large hand wheel. -- Rubber-faced aluminum pullies, 8-1/2" face x 16" dia.; accepts 6" wide abrasive sanding belts.Pulleys can be spaced to accommodate various belt & material sizes; belt loop travels over table with manual handwheel belt tension & tracking. -- Includes: Magnetic starter, dust hoods

WYSONG & MILES - 315, ...Edge Sander6" x 32" Graphite mocovered wooden platen; double 8" x 34" tilting side tables; full 180° steel end table; tilts and raises & lowers. -- 2 HP Motor; direct drive motor.

WYSONG & MILES NO. 303 COMBINATION DISK AND OSCILLATING SPINDLE SANDERThis machine is two in one. It features a 26″ disk sander with a 15″ X 34″ titling table (to 45 degrees) on one side. On the other you will find an oscillating spindle sander featuring a 24″ X 24″ tilting table (15 degrees forward and 35 degrees backward) with a 2″ X 8″ oscillating spindle. -- Power for each is provided via a 5 HP motor. A swing out arm holds a 2 gallon bucket to the side of the machine for small parts or waste. -- Machine is 220V/440V/3 Phase. -- The only repair we see is a braze on the motor mount which is a very old repair and does not effect machine operation. &#9679 This fully functional machine has been fully cleaned and checked

YALE OSO-30 Order Picker Fork Lift3,000 Lbs Cap. Narrow aisle electric order picker, powered by 24 Volt Battery. -- 3-Stage mast, max. lift height 212" and 89" lowered. -- Equipped with 4" x 42" x 19" between forks, power steering, overhead guard, comes with extra battery and battery charger. -- Used for 2,063 hours.

YALE OSO-30 Stand UP Order Picker Fork Lift with ChargerSpecifications: -- Capacity: 3,000 Lbs -- Mast: 3-Stage -- Power: 24 volt battery -- Max. lift height 212" / 89" loweredEquipped with: -- Power steering -- 4" x 42" x 19" between forks -- Overhead guard -- Battery charger

Used YAMAMOTO 30-opening, premium quality, Plywood Hot Press. -- 500 Tons pressing capacity. -- Daylight is 4.7"(120mm). -- Press plates are 54" x 108" x 1.5" (1,370 x 2,700 x 40 mm). -- Auto loader feeds charger using pusher arm to load press. -- Pie rack with automatic unloader. -- Hydraulic system with accumulation tank. -- Heated by steam. -- Professional removal and loading available at Buyer's cost.

Used YAMAMOTO 45-opening, premium quality, Plywood Hot Press. -- 500 Tons Pressure Capacity. -- Daylight is 2.75" (70 mm). -- Press Platens are 106" x 53" x 1.57" (2,700 x 1,350 x 40 mm). -- Auto loader feeds charger using pusher arm to load press. -- Pie rack with automatic unloader. -- Hydraulic system with accumulation tank. -- Heated by steam. -- This particular press was only operated for about 1-1/2 years. -- Professional removal and loading available at Buyer's cost.

YATES AMERICAN B-26 Top & Bottom Rough Lumber Planer24" x 4" Opening cap., 3/4" to 4" thickness capacity; 46" minimum unbutted length capacity;Specifications: -- (1) 75 HP DMD motor power hoisted top head, (1) 40 HP DMD motor bottom head, 8" dia. cutting circle at 3,450 RPM. -- 40 HP Hydraulic power unit for variable feed rate from 75 to 400 FPM, 12" dia. Urethane tire top feed rolls, 12" dia. non-powered lower rolls. Equipped with: -- Carbide spiral cutterheads, automatic pressure bar release (hydraulically operated), hydraulic top & bottom headlocks, anti-lap bar device, air tensioned & released chipbreaker. -- Complete with: Built-in top & bottom jointers, dust hoods, electrically interlocked safety guards, and small remote operator's console.

ZAFFARONI MLS 130 P PD MULTI-BLADE PANEL SAW: -- SpecificationsZaffaroni is the Top of the Line in Precision Multi Rip saws for Panels. Blade Depth is mechanically adjustable with a tolerance of =- 0.01 mm (0.0004"). The saw is so precise it can also be used for "V" grooving.The Saw blades project through the table from below. A double row of hold down wheels are mounted above the saw, with 24 adjustable rollers to prevent contact with the blade.Technical Characteristics: -- Working Width 1300 mm (51-1/8") -- Min. Panel Length 300 mm (11-7/8"). -- Motorized thickness adjustment from 0 - 70 mm (2-3/4"). -- Adjustable projection of the saw blades from the working from 42 - 62 mm (1- 5/8" - 2-7/16") with circular saw blades or hogger trimmer up to 280 mm diam. (11"). -- Working Table Height 1120 mm (44"). -- Transport Speed from 3 - 45 MPM (9.8 - 147.6 FPM). -- Main Motor Power 37 KW (50 HP) with Belt Drive. -- Saw Blade Spindle 80 mm x 1310 mm (3-1/8: x 51-1/2"), with double tangs and automatic anti-rotation locking clutch. -- Spindle Speed 4,000 RPM.Machine Features: -- Opening of the roller group through pneumatic cylinder with timer interlock for safety. -- Safety protection hood with sound absorbing materials to conform to ISO 7960/95 Norm. -- PLC logic control with digtital communications through bus cable.Spacer Sets: Machines require Spacer Sets and Saw Blades (not included) and pricing is available on request.

ZAFFARONI MLS 160 P MULTI-BLADE PANEL SAW: -- SpecificationsZAFFARONI is the "Top of the Line" in Precision Multi-Rip Saws for Panels. Blade Depth is mechanically adjustable with a tolerance of +/- 0.01 mm (0.0004"). The Saw is so precise it can also be used for V-Grooving.The Saw blades project through the table from below. A double-row of hold-down wheels are mounted above the Saw, with (24) adjustable rollers to prevent contact with the blade.Technical Characteristics: -- Working Width is 1,600 mm (63"). -- Max. panel pass through is 1,780 mm (70"), min. length is (320 mm) 12-5/8". -- Motorized thickness adjustment from 0 - 70 mm (2-3/4"). -- Adjustable projection of the saw blades from the working from 42 - 62 mm (1-5/8" - 2-7/16") with circular saw blades or hogger trimmer up to 280 mm dia. (11"). -- Working table height is 1,120 mm (44"). -- Material Feed Speed from 3 - 45 MPM (9.8 - 147.6 FPM). -- Main Motor Power is 55 kW (74 HP) with Belt Drive arbor. -- Saw Blade arbor 80 mm dia. x 1,310 mm (3-1/8" x 51-1/2"), with double-tangs and automatic anti-rotation locking clutch. -- Blade Arbor Speed of 4,000 RPM.Machine Features: -- Opening of the roller group through pneumatic cylinder with timer interlock for safety. -- Safety protection hood with sound absorbing materials to conform to ISO 7960/95 Norm. -- PLC Logic control with digital communications through bus cable.Spacer Sets: Machine requires Spacer Sets and Saw Blades (not included); pricing is available on request. Examples:width from......1 - 10 mm ...$ 25.45width from.....11 - 25 mm ...$ 30.15width from.....26 - 50 mm ...$ 35.60width from.....51 - 75 mm ...$ 40.15width from.....76 - 100 mm ...$ 45.20width from...101 - 125 mm ...$ 49.75width from...126 - 150 mm ...$ 54.90

ZAFFARONI MSR 160 P BS/PD MULTI-BLADE PANEL SAW (W/TOP & BOTTOM ARBORS): -- SpecificationsZAFFARONI is the "Top of the Line" in Precision Multi-Rip Saws for Panels. Blade Depth is mechanically adjustable with a tolerance of +/- 0.01 mm (0.0004").The Saw is so precise it can also be used for V-Grooving.The Saw blades project through the table from above & below. A double-row of hold-down wheels are mounted above the saw, with (28) adjustable rollers to prevent contact with the blade.The Top & Bottom shafts & wheels are connected by a quick flange system that can be removed/replaced without dismounting the bearing collars.Motorized adjustment of the depth of the saw blade projection by the touch-screen operating control(4) motorized & self-adjusting (according to material thickness) upper rubber coated rollers with grooves,(4) Idle lower polyethylene coated rollers & (1) Pair of ejector rollers at the output of the machine.Automatic locking and unlocking arbor shaft with HSK collector on the LH side controlled with electro-pneumatic device for the automatic cleaning of the coupling Safety device that features a presence and positioning sensor of the shaft; closed circuit air cooling device for the shaft bearingsSaw Blade work table with interchangeable MDF inserts.Technical Characteristics: -- Working Width is 1,600 mm (63"). -- Max. panel pass through is 1,780 mm (70"), min. length is (450 mm) 17.7". -- Motorized thickness adjustment from 0 - 70 mm (2.7"). -- Adjustable projection of the saw blades from the working from 0 - 62 mm (0" - 2.4") with circular saw blades or hogger trimmer up to 280 mm dia. (11"). -- Working table height is variable, from 970 - 1270 mm (38" - 50"). -- Material Feed Speed from 3 - 45 MPM (9.8 - 147.6 FPM). -- Main Motor Power is 45 kW (60 HP) with toothed Belt Drive arbor. -- Saw Blade arbor 80 mm dia. x 1,310 mm (3-1/8" x 51-1/2"), with double-tangs and automatic anti-rotation locking clutch. -- Blade Arbor Speed of 4,000 RPM.Machine Features: -- Opening of the roller group through pneumatic cylinder with timer interlock for safety. -- Safety protection hood with sound absorbing materials to conform to ISO 7960/95 Norm. -- PLC Logic touch screen control with digital communications through profibus cable.Spacer Sets: Machine requires Spacer Sets and Saw Blades (not included); pricing is available on request.Examples:width from......1 - 10 mm ...$ 25.45width from.....11 - 25 mm ...$ 30.15width from.....26 - 50 mm ...$ 35.60width from.....51 - 75 mm ...$ 40.15width from.....76 - 100 mm ...$ 45.20width from...101 - 125 mm ...$ 49.75width from...126 - 150 mm ...$ 54.90Example of productivity:Approx. 240 panels/hour running the machine at 49 FPM (15MPM) – considering to load 4 panels/minute) & a change-over time of approx. 10 minutes.