EXTREMA DC-250.3 TYPHOON Cyclone & Fabric Filtration Dust Collection System. Powerful two-stage dust collection drops out heavier dust particles into a drum before passing finer particles through the fan and filter.Specifications: -- (1) Fabric filter bag placed above plastic collection bag. -- 2,975 CFM rated output. -- 5 HP Induction motor. -- 14-1/4" Steel blower fan impeller is dynamically balanced. -- Collection bag snap-in ring for easy addition or removal of plastic bag. -- Filter bag filters dust particles down to (1) Micron in size. -- Low noise operation. Includes: Sturdy steel tripod cyclone mounting stand. Drum dollie (drum not included).

EXTREMA DC-275.3 TYPHOON Cyclone & Fabric Filtration Dust Collection System. -- Powerful two-stage dust collection drops out heavier dust particles into a drum before passing finer particles through the fan and filter. -- (2) Fabric filter bags placed above plastic collection bags. -- Air volume output rated @ 4,850 CFM. -- 7.5 HP Induction motor. -- 14-3/4" Steel blower fan impeller and is dynamically balanced. -- Collection bag snap-in ring for easy addition or removal of plastic bag. -- Filter bags filter dust particles down to (1) Micron in size. -- Low noise operation. -- Includes: Sturdy steel tripod cyclone mounting stand and drum dolly. (drum not included).

EXTREMA DC-3050.3 TYPHOON Fabric Filtration Modular Dust Collection System. -- With 1-micron dust filtration efficency this collector will make your shop cleaner, healthier, and more productive. -- (2) Fabric filter top bags are mounted above individual plastic collection bags. -- The multi-bag system is placed on sturdy steel legs in a horizontal series. -- 3,075 CFM Output with single-stage blower. -- Additional filtration sections can be easily added. -- Heavy Duty 5 HP blower motor. -- 13" Steel blower fan impellers are dynamically balanced. -- Collection bag snap-in rings for easy addition or removal of plastic bags. -- 1-Micron filter bags with 6 mil plastic bottom collection bags are standard. -- Options: Remote control and drum storage kit. -- Also available in Single Phase.

EXTREMA DC-3075.1 TYPHOON Fabric Filtration Modular Dust Collection System.With 1-micron dust filtration efficiency this collector will make your shop cleaner, healthier, and more productive. -- (3) Fabric filter top bags are mounted above individual plastic collection bags. -- The multi-bag system is placed on sturdy steel legs in a horizontal series. -- 4,550 CFM Output with single-stage blower. -- Additional filtration sections can be easily added. -- Heavy Duty 7.5 HP motor with push button control and motor starter. -- 13.5" Steel blower fan impellers are dynamically balanced. -- Collection bag snap-in rings for easy installation and removal of bags. -- Filter bags filter out dust particles down to (1) Micron in size; 6 mil thick plastic bottom collection bags are standard. -- Options: Remote control and drum storage kit.

EXTREMA DC-3075.3 TYPHOON Fabric Filtration Modular Dust Collection System.With 1-micron dust filtration efficiency this collector will make your shop cleaner, healthier, and more productive. -- (3) Fabric filter top bags are mounted above individual plastic collection bags. -- The multi-bag system is placed on sturdy steel legs in a horizontal series. -- 4,550 CFM Output with single-stage blower. -- Additional filtration sections can be easily added. -- Heavy Duty 7.5 HP motor with push button control and motor starter, 12" inlet. -- 13.5" Steel blower fan impellers are dynamically balanced. -- Collection bag snap-in rings for easy installation and removal of bags. -- Filter bags filter out dust particles down to (1) Micron in size; 6 mil thick plastic bottom collection bags are standard. -- Options: Remote control and drum storage kit.

HOLZ-HER 1327 SPRINT CLASSIC SPECIAL EDGEBANDER + EVA/PUR GLUING TECHNOLOGY: -- Note: This is a "SPECIAL MACHINE for THIN TAPE Only". -- Specifications: Features the HOLZ-HER patented dual "GLU-JET" EVA & PUR Zero Joint Technology System.Edgebanding capacity: Edge thickness min./max. 0.4 - 8 mm (0.02 - 0.31"); coiled material 0.4 - 3 mm (0.016 - 0.157").Workpiece thickness: 6 - 60 mm (0.23" - 2.36"); Workpiece width min. of 65 mm (2.56").Workpiece length: Min. 160 mm (6.29"); variable feed speed 10 - 18 MPM (33 - 59 FPM). Machine Infeed: -- "Open Space" for Pre-milling Station "1802": (2) 2.0 kW (2.68 HP) - 12,000 RPM motors.NOTE: This machine is not equipped with the Premilling Station, but it can be added. -- Edge Magazine "1903":For coil & strip processing; utilizes motion detector to ensure accurate, troublefree positioning of edge material.Exclusive "Tractor Belt Feed System": Edge guide equipped with automatic guillotine lockout for safety.3° Approach angle allows easy feeding of solid wood edges. -- Pressure Section "1913 Mot":1-Axis Servo controlled adjustment of the edge thickness.Pneumatic Plunge controlled pressure section with: (1) Large driven roller and (2) cantered idle rollers. -- Gluing System "GJ301Auto":Glue Jet Hybrid Technology: Processes "EVA" or "PUR" glue in cartridge or granulate form.Motorized programmable glue nozzle (upper glue line); height positioning. approx. 3-minute heat up time. Workstations: -- End Trimming Unit "1918P": Front & Rear; 2 x 0.45 kW (0.6 HP) - 9,000 RPM each motor.For Straight or Chamfer trimming with: "UNI-POINT Axis for "PCS" pneumatic changeover/swiveling up to 10° bevel. -- Combination Trimming Unit "1827": Top & Bottom; 2 x 0.65 kW (0.87 HP) - 12,000 RPM each motor; for T & B Flush/Bevel/Radius trimming. - "ProLock" Clamping System for rapid tool change.Manual edge radius adjustment up to 3 mm & chamfer adjustment up to 15° with a max. edge thickness of 6 mm. -- "Open Space" for 2nd T & B Trimming Unit.NOTE-1: This machine is not equipped with the 2nd T & B Trimming Unit, but it can be added. -- "Open Space"for Profile Scraping Unit "1929P". NOTE-2: This machine is not equipped with the Profile Scraping Unit "1929P", but it can be added. -- "Open Space" for Finish Scraping "1964". NOTE-3: This machine is not equipped with the Finish Scraping "1964", but it can be added. -- "Open Space"for Buffing Unit "1940". NOTE: This machine is not equipped with the Buffing Unit "1940", but it can be added. Operator Interface: -- HOLZ-HER "PPC 231" Power-PC + "Windows-like" Operating System. - 15" SVGA Flat "Touchscreen" control.USB Connection & Ethernet network connection ready; programs can be easily created and recalled at will. Graphic interface makes programming easy; icon of each unit may be brought up on the screen to show the Operator the status of the unit and the parameters that can be programmed.Edgebander can be operated manually when required, without necessity to write a program.C

HOLZ-HER 1329 SPRINT PERFORMANCE EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) + EVA/PUR GLUING TECHNOLOGY: -- Specifications:Features the HOLZ-HER Patented Dual "GLU-JET" EVA & PÜR Zero Joint Technology System.Edge thickness min./max. 0.4 - 12 mm (0.016 - 0.472"); coiled material 0.4 - 3 mm (0.016 - 0.157").Panel thickness 8 - 60 mm (0.236 - 2.362"); workpiece width min. of 60 mm (2.36"); workpiece length min. 160 mm (6.29"). Programmable Logic Control (PLC) for Pre milling, edge feed, glue application, end trimming, flush trimming, radius trimming, scraping, corner rounding, and buffing. -- Pre milling Station (1802):(2) 2.0 kW (2.68 HP) - 12,000 RPM motors; equipped with: "ProLock" quick change flange including height adjustment for optimum utilization of cutters. -- Edge Magazine (1901):Small 3° feed angle thanks to nozzle design with easy feeding of coils, strips & up to 3 mm and solid wood edging up to 15 mm (0.059").Exclusive "Tractor-Belt Feed System", edge guide equipped with automatic guillotine lock-out for safety. -- Pressure Section (1913 Mot):Servo-controlled pressure section with (1) large driven roller and (2) cantered idle rollers. Straight and tapered pressure rollers for perfect glued joints. -- Gluing System (GJ301 Auto):"GLU JET" Hybrid Technology "thin film technology processes EVA or PÜR Glue in cartridge or granulate form.Motorized, programmable glue nozzle (upper glue line) height positioning. Automatic reload of the glue cartridges or granulated. Workstations: -- End Trimming Unit (1918-P):Front & Rear - (2) 0.35 kW (0.5 HP) - 9,000 RPM motor each; unipoint swivel axis for no re-indexing when changing from flush to bevel end trim (0° - 10° bevel)."PCS" programmable pneumatic changeover from flush to bevel. -- Multi-Function Trimming Unit (1827MOT4): (2) 0.65 kW (0.87 HP) - 12,000 RPM each motor, Servo motors: (1) for horizontal copy wheel & (1) for tool spindle position; programmable top & bottom unit. Unipoint design with no second adjustment with pneumatic, programmable tilt action for changing the degree of bevel.Digital counters for vertical copy wheel position and pneumatic air cylinder for in/out pre-positioning of trimming motor. -- Corner Rounding Unit (1833 MOT4):(2) motors with 0.22 kW (0.30 HP) - 9,000 RPM, for linear edge trimming or vertical corner rounding with (4) Servo programmable positioning motors; Up to 3 mm edge thickness and workpiece thickness min./max.8 - 60 mm (0.31 - 2.36"); max. feed speed 18 MPM (59 FMP) up to 25 mm panel thickness; 26 - 38 mm panel thickness,16 MPM (52 FPM); 39 - 60 mm panel thickness, 2 MPM (6 FPM). -- Profile Scraping Unit (1929-MOT2): Top/Bottom Servo motor controlled, programmable knife position for PVC edges, reversible insert carbide knives.Equipped with air jet blowers and chip collector box. -- Glue Scraping Unit (1964):Flat, Top/Bottom, ball bearing guided and pneumatic controlled. -- Buffing Station (1940):Top & Bottom buffing motors with - 150 mm

HOLZ-HER 1488V TRIATHLON (W/PRE-MILL & CORNER ROUNDING): -- Specifications:PC Controller which has the ability to program all functions including, thickness, edge feed, glue application, side pressure, end trimming, flush trimming, bevel/radius trimming, shaping, buffing. Virtually eliminates set-up time by selecting & loading program that automatically activates all functions simultaneously.Basic Capacity Data: Max. 1" (25 mm) solid wood banding, thin PVC, veneer, HPL & 3 mm PVC cap., 2-3/8" max. panel thickness and 7" min. panel length.Front-End Equipped With: -- Granulate Gluing System (#1907), w/flat glue-nozzle only 3° angle of approach ideal for solid wood edgebanding & "quick melt" feature. -- Automatic Edge-Magazine (1901) for coil, strip & solid wood edgebanding with TRACTOR-BELT feed system, with Heavy Duty guillotine for 4 mm PVC. -- Pressure Section (1926K MOT) with (3) large dia. rollers, each w/individual pneumatic plunge and pressure control; Programmable with servo motor positioning. Powered 1st roller with electronic speed control synchronized with chain feed speed.EDGEBANDING WORKSTATIONS: -- End Trimming Unit (#1916.1), (2) "HF" motors @ (1 HP - 2,480 RPM ea.) with "Uni-Point Swivel", quick change from flush to 0° - 15° bevel programmable from operator panel. -- Flush Trimming Unit (#1962), (2.6 HP - 200 Cy HF motors), w/servo controls, (3) motors, for compl. workstation forward/backward, vertical copy-wheels +/-. -- Fine/Bevel/Radius Trimming Unit (#1966M), w/5-axis servo motors, (1.5 HP - 200 Cy HF motors), bevels 0° - 45°, plus SIKO digital readouts. -- Scraper Unit (#1927), "Super Duty" for positively smooth finishing thick PVC for radius range from 2 - 5 mm, vertical & horizontal tracing wheels, positioning enabled through (1) servo motor function from control panel, as well as SIKO readouts for easy setup. -- Edge Shaper (#1932 MOT), w/jump control for vertical or horizontal shaping or grooving, 3.8 KW (5 HP) spindle motor, 12,000 RPM spindle speed, max. cutter dia. 135 mm (5.3"), max. cutter width 60 mm (2.36"), servo motor positioning for shaper base and SIKO digital readouts. -- Flat Glue Scraper (#1964), top & bottom for removal of potential glue squeeze-out w/air pressure nozzles to prevent shavings build-up. -- Jump Buffing Unit (#1944), w/programmable jump action for cleaning & polishing of edges (two 0.25 HP - 3,600 RPM motors), tilts 0° - 5°. -- Edge Sanding Unit (1935), vertical oscillating, belt size 120 x 2100 mm (4.75 x 82.75"), pneumatic pressure control for sanding pad, anti-dubbing device for leading & trailing edges.Equipped with and Includes: -- Microprocessor with color LCD screen, 90% of all set-ups can be adjusted from the control panel, programmable for a large variety of edges like solid lumber, veneer strips or coils, HPL, thin & thick PVC. Line control so there are no mechanical limit switches along the chain track. -- Variable feed speed from 8 - 24 MPM (26 - 67 FPM), panel overhang

HOLZ-HER 1488 TRIATHLON EDGEBANDER (W/PRE-MILLING & CORNER ROUNDING) + LIGMATECH -ZR01 Return Conveyor -- Specifications:Working Capacity: Max. 1" (25 mm) solid wood banding. thin PVC, Veneer, HPL & 3 mm PVC cap.; 60 mm (2.37") max. panel thickness, and 140 mm (5-1/2") min. panel length.Front-End equipped with: -- Pre-milling Unit: (2) 2.2 kW (3.0 HP) - 12,000 RPM; (1) jump spindle with digital indicators for positioning. -- Gluing System: "ULTRA-GRANUPRESS" System with: Flat glue nozzle only 3° angle of approach ideal for solid wood edgebanding & "quick melt" feature. -- Automatic Edge Magazine for: Coil, strip & solid wood edgebanding with TRACTOR-BELT feed system; Heavy-Duty guillotine for 4 mm PVC. -- Pressure Section with: (3) Large dia. rollers, each w/individual pneumatic plunge and pressure control; programmable with Servo motor positioning; powered 1st roller with electronic speed control synchronized with chain feed speed.Edgebanding Workstations: -- End Trimming Unit: (2) 0.75 HP - 6,800 RPM ea. "HF" Motors with: "Uni-Point Swivel", quick change from flush 0° - 15° bevel programmable from operator panel; Servo controls. -- Flush Trimming Unit: (2) 2.6 HP - 12,000 RPM - 200 Cy HF motors; Servo controls. -- Fine/Bevel/Radius Trimming Unit: (2) 1-1/2 HP- 12,000 RPM - 200 Cy HF motors; bevels 0° - 45°, Servo controls + SIKO digital readouts. -- Corner Rounding Unit: (2) "HF" Top motors & (2) HF Bottom motors for trimming leading-and-trailing upper-and-lower edge/corners; trailing edge (4 x 3/4 HP - 12,000 RPM - 300 Cy HF motors; 2 mm or 3 mm radius cap. -- Profile Scraper Unit: "Super Duty" for positively smooth finishing thick PVC for radius range from 2 - 5 mm; vertical & horizontal tracing wheels, positioning enabled through (1) Servo motor function from Control Panel; SIKO readouts for easy setup. -- Buffing Unit: (2) Lateral buffing wheel positioning motors with Oscillating & Programmable Jump Action for cleaning & polishing of edges (two 0.25 HP - 3,600 RPM motors); tilts 0° - 5°, Servo controls.Equipped with and Includes: -- PPC 231 Controller with 15" LCD color screen: 90% of all set-ups can be adjusted from the Control Panel; programmable for a large variety of edges like solid lumber, veneer strips or coils, HPL, thin & thick PVC; line control so there are no mechanical limit switches along the chain track. -- Variable feed speed from 8 - 20 MPM (26 - 65 FPM); panel overhang beyond chain 35 mm (1.38"); features automatic track pad lubrication. -- Factory Documentation: Operating and Spare Parts Manuals. -- Actual Model is: HOLZ-HER 1488 TRIATHLON + LIGMATECH ZR01

HOLZ-HER AURIGA 1308 XL EDGEBANDER (W/PREMILL & CORNER ROUNDING): + "GLU JET" EVA/PUR GLUING TECHNOLOGY: -- Specifications:Servo controls on the following: Pressure beam height; Top & Bottom trimmer; 3 mm radius scraper; auto-tilt on end trim; programmable corner rounder; pneumatic finish scraper. (1) Centrally located hand wheel for manual raising & lowering of the top pressure beam. Rigid workpiece support extending 380 mm; manual central lubrication of the transport chain.Feed speed: 10 MPM (33 FPM). -- Working Capacity: Edge thickness: Min./max. 0.4 - 3 mm (0.02 - 0.12"); coiled material; optional with flush cutters max. 6 mm (0.24").Panel thickness: 6 - 60 mm (0.236 - 2.362"); workpiece width min. of 65 mm (2.559"); workpiece length min.160 mm (6.299"). -- Premilling Station "1801":(2) x 1.2 kW (1.6 HP) - 12,000 RPM Motors; diamond cutter heads with ProLock quick clamping system. Quick-Lock adjustable infeed fence with digital indicator. -- Edge Magazine "1903":For coil & strip processing; utilizes motion detector to ensure accurate, trouble free positioning of edge material.Exclusive "Tractor-Belt feed System": Edge guide equipped with: Automatic guillotine lockout for safety.3° Approach angle allows easy feeding of solid wood edges. -- Pressure Section "1912-3P":With (1) large driven (synchronized with feed speed) roller and (2) cantered idle rollers, adjustable by hand wheel and scale. -- Glue Jet systemUpper glue line height positioning is set automatically with hold down beam setting.Heat up time to ready stage takes only (2 - 30) minutes!NOTE: Granulate requires an "optional" hopper. - Select our "Select Literature" link on the detail page and scroll to "Page-8" for more details.Workstations: -- End Trimming Unit "1918P": Front & rear 2 x 0.45 KW (0.6 HP) - 9,000 RPM motor each,Uni-point swivel-axis for no re-indexing when changing from flush to bevel end trim (0° - 10° bevel)."PCS" programmable pneumatic change-over from flush to bevel. -- Flush/Bevel/Radius Combination Trimming Unit "1827P": Flush 6 mm, radius 3 mm trimming, servo controlled, 2 servo motors (1) for horizontal copy wheel & (1) for tool spindle position).Programmable top & bottom unit 2 x 0.65 KW (0.88 HP) - 12,000 RPM each motor.Uni-Point design with no second adjustment, pneumatic, programmable tilt action for changing the degree of bevel,Digital counters for vertical copy wheel position and pneumatic air cylinder for in/out pre-positioning of trimming motor. -- Corner Rounding Unit "1832": (1) Motor 0.22 KW (0.30 HP) - 9000 RPM for up to 3 mm edge thickness.Work-piece thickness min./max. 12 - 60 mm (0.473 - 2.362"), Max. feed speed 10 MPM (33 FMP). -- Profile Scraping Unit "1929":Top/Bottom, servo motor controlled/programmable knife position, vertical copy wheel adjustment with quick setting spindle - for PVC edges,Reversible insert carbide knives, equipped with air-jet blowers and chip collector box. -- Glue Scraping Unit "1964":Flat surface, top/bottom,

HOLZMA PROFIMAT HPL 500 38/16 REAR LOAD, AUTOMATIC PANEL SAW: -- Specifications: 149.6" (3,800 mm) Cutting length & pull-back; 6.7" (170 mm) max. main blade projection; 40 HP (29.8 kW) Main & 3 HP (2.2 kW) scoring motor. -- Saw carriage: Infinitely variable speed from 0 - 492 FPM (0 - 150 MPM), constant return of 492 FPM (150 MPM).Carriage is electronically & automatically controlled (cutting height & length) through the CADmatic according to the material/program being processed."Power-Loc" quick change system for fast and easy saw blade change.NC Controlled scoring saw adjustment from the control panel during operation -- Pusher Fence:Rack & pinion digital drives with AC Servos on both sides, forward speed 295 FPM (90 MPM), return speed 295 FPM (90 MPM).(7) Material clamps which open up to 6.7" (170 mm): (3) Standard clamps with two fingers & (4) clamps with one finger.(4) Trimming rakes for thin strips/scrap removal are attached at the clamps. -- Operator Interface:HOLZMA "Power Touch Control" IPC multi-tasking controller with Windows "7 PRO" + "CADmatic 4.0 PRACTIVE" operating system;Intel i5 Dual-core Processor, Intel HD graphics card, 4GB RAM, SATA 2-250GB hard drive, (6) USB ports, (1) serial port, ATI/DVI video port, Standard industrial keyboard connection,21.5" LCD "Touch-Screen" monitor with real-time moving 2D & 3D graphics (displays cutting dimensions & error diagnostic); virtually unlimited cutting dimension memory.(2) Ethernet 10/100 interface connections; downloading from office PC is possible. -- Rear of machine: Profile rails & "Combi-rollers" at 50 mm centers; (2) integrated front & cross-aligning units before cutting to prevent off-set panels within the same book. -- Front of machine: (3) Air flotation tables 85" x 31.5" (2,160 x 800 mm) with (1) central blower unit. -- Rear Lift Table:7-Ton (14,000 LBS), 4-Column electro-hydraulic powered rear lift table running lengthwise with fork cut-outs, 150" x 63" (3,800 x 1,600 mm) capacity. Powered rollers are 4.2" (107 mm) dia x 7.79" (198 mm) spacing, 39 FPM (12 MPM) infeed/outfeed speed; Feeding material from (3) sides is possible with additional roller conveyors.22" (560 mm) Max. bunk height from floor level; 30.7" (780 mm) max. bunk height with a pit or risers; -- Complete With: Holzma's Unique "EcoPlus" System offers energy savings up to 20%; Includes Standby button & IE3 energy efficiency Motors rating.Angular cross-cut fence; Automatic side pressure device integrated into the saw carriage for cross-cutting, the machine cuts left to right to the cross-cut fence.Front & rear forks electronically & automatically controlled through the CADmatic according to the material/program being processed.Min. side aligning dimension 0" (0 mm), max. side aligning dimension 149" (3,800 mm)."Power-Loc" quick blade change system for main/scoring blades. -- Options Include: &#9679 (1) Non-Powered in/out-feed staging conveyor with fork cut-outs as pictured. &#9679 Micro In-feed for thin an

HOMAG KAL 210 AMBITION 2260 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:Coiled stock min/max. Edge thickness 0.4 - 3 mm (0.016. - 0.118"), Strip material min/max Edge Thickness 0.4 - 6 mm (0.16 - 0.234"). -- Panel stock min/max. thickness12 - 40 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18"). -- In-feed Fence: Adjustable in-feed fence with manual digital indicator positioning. -- Pre-Milling Station: Two 3.0 kW (4.0 HP), 150 Hz, 9,000 RPM Motors; equipped with trimming column, (2) horizontal and cross slides with spindle adjustment, electro-pneumatic horizontal jump movement of the first motor;Includes electronic frequency inverter for control of motor speed and braking, two (2) dust extraction hoods, an air-jet panel blow-off device & SIKO digital counters for adjustments. -- Panel Pre-Heater: the Pre-heater brings the panel to an appropriate temperature for better adhesion; this is especially beneficial in cooler temperatures. -- Multi-Purpose Magazine: 2-Coil magazine expands capability by running coiled material & strips, magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panel on the edgebanding. -- Gluing System: (EVA - Hot Melt) QA 3 -Quick Melt Overhead Unit & heated roller applicator; digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allows for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gates, lower melting unit equipped with automatic glue level control. Melting capacity: 12 KG/Hr (26 LBS/Hr). -- Pressure Section: Automatic pressure zone adjustment (Servo), (1) large 160 mm dia. driven & (6) 70 mm dia. idle rollers, pneumatic pressure control depending on edgebanding material used. -- WORKSTATIONSEnd Trimming Unit HL 81: 0.8 KW (1.0 HP) x 2 - 200 Hz, 12,000 RPM Motors. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer 30° to straight cut. -- Top & bottom Flush Trimming Unit: Top & bottom, 0.4 kW (0.74 HP) x 2 - 12,000 RPM Motors; Height adjustment with the top pressure-beam and tilting range +/- 1°. -- Profile/Bevel/Corner Rounding Unit FF 12: Multi-function 0.4 KW (0.54 HP) x 2 - 12,000 RPM Motor to fine trim the edge overhangs at the work-piece upper & lower edge, as well as trimming around the front & rear vertical edge. Max. feed speed 20 MPM (65.6 FPM) -- Profile/Bevel Scraping Unit PN 10: Top & bottom for thick PVC/ABS, pneumatically activated/adjustment. -- Flat Glue Scraper Unit: Top & bottom, pneumatically activated to remove potential glue squeeze-out. -- Buffing Unit FA 11: Top & bottom edge buffing/polishing, pneumatically activated. -- Operator & Machine Control:HOMATIC PC 22 Power Control w/Touch Screen: Controller functions in Windows environment and features: Keypad w/LCD flat-screen display, fault diagnostic, OS9 real-time operating syst

HOMAG KAL 310/4/A3/S2 EDGEBANDER (W/PRE-MILLING): -- Specifications:Working Capacity: 0.3 - 3 mm Edge thickness cap., min. panel width 22 mm; max. panel thickness 60 mm; Dual speed -- Equipped with: Pre-Milling Unit 3481: (2) motors, 3 kW, 9000 RPM each, pneumatic controlled/jump milling spindles and adjustable, manual with digital indicator in-feed fence. -- Hot Melt Glue System "QA 34" Quick-Melt Unit: with heated glue roller; -- Edge Magazine Unit 2456: Automatic (2) coil/strip magazine, coils 0.3 - 3.0 mm. -- Pressure Section: Pressure roll section with (3) rollers, (1) large dia. driven & (2) idle rollers; with pneumatic pressure control for straight edges -- HOMATIC "NC 21" Power Control System: Controller operates in Windows-XP environment; Keypad w/LCD display, fault diagnostic, etc.; diagnostic analysis from HOMAG service support via Modem. -- Workstations:End Trimming Unit: (2) motors, 0.18 kW - 12,000 RPM each, to cut excess edge on the front & back of the panel. -- Flush/Pre-Trimming Unit 3201: Top & bottom trim station, 0.55 kW - 12,000 RPM +/- 1° angle adjustment, manual positioning with digital counters. -- Fine/Bevel Trim Unit 3216: (2) motors 0.4kW - 12,000 RPM each, manual positioning with digital counters -- Profile Edge Scraping Unit: with electro-pneumatic adjustment -- Buffing Unit 4402: Top and bottom with oscillation. (2) motors, 0.25kW, 2850 RPM -- Complete with & Features:Electronic DC brakes on all trim motors; sound cabin for all workstations. -- Adjustable outboard panel support with swing out arms for up to 800 mm. -- 80 mm Feed track pads; manually adjusted V-groove belt on top pressure beam and Sound/Safety enclosure over workstations. -- Actual Model is HOMAG KAL 310/4/A3/S2Note: This machine has a new display and a new back up one as well!

HOMAG BMG 310/42/F/K CNC MACHINING CENTER (5-AXIS): -- Specifications:Working field: "X" Axis if 4,200 mm (165.3"), "Y" axis 1,600 mm (63"), "Z" axis stroke is 300 mm (11.1"); max. material thickness of 200 mm (7.9"), max. material thickness when using 100 mm high Vacuum cups. -- Positioning Speed: "X" & "Y" Axis positioning speed is 80 MPM (262 FPM), "Z" axis position speed 30 MPM (98 FPM); AC Brushless Servo motors with digital drive and THK linear guides ensure high speeds with a smooth acceleration/deceleration. -- Worktable:(8) K-Table tubeless support rails with LED setup assistance, (6) lifting bars for large panels; Laser device for positioning support rails & vacuum pods.(8) Pneumatic front stops, (5) pneumatic backstops, (2) LH pneumatic side stops, (2) RH pneumatic side stops, (2) independent work zones. -- Machining Unit: (1) 20 HP (15 kW) liquid cooled "FLEX5C+" 5-AXIS electro-spindle router with HSK-F63 adaptor, (1,000 - 24,000 RPM).(22) Total ATC positions with: (1) 14-Position plate-type rotary tool changer mounted at the back of the machine head, & (1) 8-position tool rack mounted on the side of the machine. -- Operator & Machine Control:"PowerTouch PC 87" control, 17" TFT color monitor with "Full Touch" operation + "WoodWOP 6.1" operating system.Icon driven software with a graphical interface to allow the operator to quickly & efficiently create programs & diagnose malfunctions in simple terminology.Multitasking "REAL-TIME", 2/3D graphics operating system, input/output modules, axes override, 4/5-axis interpolation, diagnostic graphics aid for programming, machine data & tool management. ETHERNET connection (cables not included). -- Complete with:Hand held Pendent control; Chip belt conveyor; (2) 100 m³/Hr vacuum pumps; safety barrier/perimeter protection system; scrap conveyor; user & maintenance manuals with wiring diagrams, parts & operation on CD. -- Actual Model is HOMAG BMG 310/42/F/K.

HOMAG EDGETEQ S-500 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:0.3 - 3 mm (0.012 - 0.125") edge material thickness; 8 - 60 mm (0.3' - 2.375") panel thickness; 160 mm (6.375") min. panel length and 70 mm (2.75") min. panel width.High flexibility is achieved as all edge materials can be processed: 0.3 mm Melamine, up to 3 mm ABS, PP, PVC and wood as coil material.For perfect high-gloss parts, important components such as the motor-driven top pressure and the automatic adjustment of the glue joint scrapers are used.Special tracing elements are ideal for processing of acute angled or obtuse angled parts or parts with hinge holes and transversal grooves.Variable Production Feed Speeds from 16 - 30 MPM (52 - 98 FPM). -- Equipped with: Separating agent spraying unit. -- Pre-milling Station: (2) Motors @ 2.25 kW (3.0 HP), 12.000 RPM; LH & RH rotation w/pneumatic jump control for chip-free and clean panel edges. Equipped with diamond cutter heads. -- Infeed fence with Servo motor positioning. -- Infrared Radiant Quartz Heating Unit between glue roller and pressure section. -- Automatic Edge Magazine for strip & coil stock, strips 0.4 mm - 12 mm (0.015 - 0.47"), coils up to 3 mm PVC with "HD" guillotine. -- "Quick Change" Glue Tank for maintenance, glue type & color change. -- Pressure Section: 1st. Roller driven plus (2) idle rollers, timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- HOMAG "PowerTouch control, memory: 256 MB RAM, 1 GB Flash Card Drive. -- Workstations: End Trimming: (2) Motors @ 0.35 kW (1/2 HP) - 12,000 RPM; automatic chamfer from control panel 0°- 15°. -- Multistage MS40 Flush/Bevel-Fine/Radius Trimming Unit:Top/bottom: (2) Motors, 0.55 kW (3/4 HP) - 12,000 RPM, auto-tilt positioning 0° - 25°; with combination flush/radius/chamfer cutterheads. -- Multifunctional trimming unit MF60 Servo trim - Horizontal and vertical tracing wheels, equipped with brushless multi-axis Servo motors for positioning of work unit & horizontal copy wheels for quick changeover. Includes (3) positioning options: Profile 1, profile 2, and flush trimming; nested top copy system. -- Corner Rounding Unit: (1) 0.35 kW (1/2 HP) - 12,000 RPM Motor for leading & trailing edges, vertical corner rounding of panels; either radius or chamfer cutters can be mounted; 3 mm max. edge thickness. -- Scraping, multi-profile (PVC): Top/bottom with (2) profiles (1 mm and 2 mm or 3 mm instead of 2 mm), Servo control positioning of vertical & horizontal copy wheels. PVC scrape collection box. -- Flat Glue Joint Scraping Unit: Flush top/bottom on panel surface with floating insert knives. -- Buffing Unit: Top & bottom (2) motors, 0.10 kW (0.125 HP) 2,800 RPM. -- Operator Interface: HOMAG powerTouch2 control with clearer structure, 30% faster, more intuitive, more ergonomically comfortable, and remote service Support. 22" Color HD wide touch-screen display, soft keypad

HOMAGDRILLTEQ V-200 CNC MACHINING CENTER (VERTICAL/W/BORING): -- Specifications: Flexible "Vertical" Machining Center with "BORING": Uses less than 5 sq. meter of valuable floor space in addition to an innovative panel handling system. -- Working Cap.Max. workable part size for "X" axis is 120" (3,050 mm); "Y" axis 33.4" (850 mm); max. part thickness 3.1" (80 mm).Min. worktable part size for "X" axis is 7.8" (200 mm); "Y" axis 2.75" (70 mm); min. part thickness of 0.31" (8 mm). - Automatic infeed & outfeed from the LH or RH side. -- Positioning SpeedThe "V-200" can reach movement speeds of 164 FPM (50 MPM) in "X" & "Y" axis & 50 FPM (15 MPM) in "Z" axis with total safety, providing an unmatched working capacity. -- Boring Unit(1) 3 HP (2.3 kW); Variable speed from 1,500 - 7,500 RPM motor; (13) independent spindles with: (8) spindles in "X" axis & (5) spindles in "Y" axis.(6) Horizontal spindles with (2 + 2) in "X" axis & (1 + 1) in "Y" axis; boring block has "QUICK CHANGE" spindle system. -- Operator & Machine ControlHOMAG "POWERTOUCH" + Windows + WoodWOP Operating System; "IntelCore 2 DUO" Processor.21" TFT Monitor; international keyboard, soft touch keypad & industrial mouse; RS-232 Serial ports, USB ports; (1) 1.44 MB floppy disk drive, (1) CD RW drive, modem, Ethernet connection.Real-time multitask processing; programs can be transferred via diskette or downloading by wire is possible. -- Complete with:Pneumatic part clamping devices; sound enclosure and complete set of safety devices. -- Options Include:(1) "X" Grooving Saw; 9,000 RPM, max. saw blade dia. 100 mm.(1) 12 HP (9 kW) Electro Spindle router with manual Quick-Change adaptor; variable speed from 6,000 - 24,000 RPM. -- Actual Model is: HOMAG DRILLTEQ V-200 OPTIMAT BHX 055.

HOMAG AMBITION 2240 PRODUCTION EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Working Capacity: Coiled stock min/max Edge thickness 0.4 - 3 mm (0.016. - 0.118"), Strip material min/max Edge Thickness 0.4 - 6 mm (0.16 - 0.234"),Panel stock min/max thickness 12 - 40 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18") -- In-feed Fence:Adjustable in-feed fence with manual digital indicator positioning. -- Pre-Milling Station:Two 3.0 kW (4.0 HP), 150 Hz, 9,000 RPM Motors; equipped with trimming column, (2) horizontal and cross slides with spindle adjustment, electro-pneumatic horizontal jump movement of the first motor.includes electronic frequency inverter for control of motor speed and braking, two (2) dust extraction hoods, air jet panel blow-off device & SIKO digital counters for adjustments. -- Panel Pre-HeaterPre-heating the panel brings the panel to an appropriate temperature for better adhesion; this is especially beneficial in cooler temperatures.Quartz lamp for heating substrate edge before glue application improved edge quality and optimum bonding. -- Multi-Purpose Magazine:A multi-purpose 2-coil magazine expands capability by running coiled material & strips. Magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panelon the edgebanding. -- Gluing System: (EVA - Hot Melt)QA 3 - Quick Melt Overhead Unit & heated roller applicator digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allows for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gatesLower melting unit equipped with automatic glue level control. Melting capacity: 12 kG/Hr (26 Lbs/Hr) -- Pressure Section:Automatic pressure zone adjustment (Servo), (1) large 160 mm dia. driven & (6) 70 mm dia. idle rollers, pneumatic pressure control depending on edgebanding material used.Work Stations End Trimming Unit HL 81:0.8 kW (1.0 HP) x 2 - 200 Hz, 12,000 RPM Motors. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer 30° to straight cut. -- Top & Bottom Flush Trimming Unit:Top & bottom, 0.4 kW (0.74 HP) x 2 - 12,000 RPM Motors; Height adjustment with the top pressure-beam and tilting range +/- 1°. -- Profile/Bevel/Corner Rounding Unit FF 12:Multi-function 0.4 kW (0.54 HP) x 2 - 12,000 RPM Motor to fine trim the edge overhangs at the work-piece upper & lower edge, as well as trimming around the front & rear vertical edge. Max. feed speed 20 MPM (65.6 FPM) -- Profile/Bevel Scraping Unit PN 10:Top & bottom for thick PVC/ABS, pneumatically activated/adjustment. -- Flat Glue Scraper Unit:Top & bottom, pneumatically activated to remove potential glue squeeze-out. -- Buffing Unit FA 11:Top & bottom edge buffing/polishing, pneumatically activated.Operator Interface: HOMATIC PC 22 Power Control w/Touch Screen:Controller functions in Windows

HOMAG AMBITION 2262 (KAL 210) EDGEBANDER (W/PRE-MILL & CORNER ROUNDING); PRODUCTION EDGEBANDER): -- Specifications: Working Capacity: Coiled stock min./max. Edge thickness 0.4 - 3 mm (0.016. - 0.118"); strip material min./max. Edge Thickness 0.4 - 6 mm (0.16 - 0.234").Panel stock min./max. thickness 12 - 40 mm (0.472" - 1.574"). Panel Overhang 30 mm (1.18"). -- Infeed Fence:Adjustable infeed fence with manual digital indicator positioning. -- Pre-milling Station:(2) 3.0 kW (4.0 HP), 150 Hz, 9,000 RPM Motors; equipped with: Trimming column, (2) horizontal & cross-slides with spindle adjustment.Electro-pneumatic horizontal jump movement of the 1st motor; includes electronic frequency inverter for control of motor speed and braking.(2) Dust extraction hoods, air jet panel blow-off device & SIKO digital counters for adjustments. -- Panel Preheater:Preheating the panel brings the panel to an appropriate temperature for better adhesion; this is especially beneficial in cooler temperatures.Quartz lamp for heating substrate edge before glue application improved edge quality and optimum bonding. -- Multipurpose Magazine:2-Coil magazine expands capability by running coiled material, strips, and solid wood bands. Magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table allowing the Operator to center the panelon the edgeband. -- Premelting System: Overhead Premelting Unit -- Gluing System: EVA - Hot Melt.QA 34 - Quick Melt Overhead Unit & heated roller applicator digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allow for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gates.Lower melting unit equipped with: Automatic glue level control; melting capacity: 12 kG/h (26 Lbs/Hr). -- Pressure Section:Manual adjustment with digital counter: (1) Large 160 mm dia. driven & (6) 70 mm dia. idle rollers; pneumatic pressure control depending on edgebanding material used.WORKSTATIONS: -- End Trimming Unit:(2) 0.8 kW (1.0 HP) - 200 Hz, 12,000 RPM Motors to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer 30° to straight cut. -- Rough/Pre-trimming Unit:Top & bottom, (2) 0.55 kW (0.74 HP) - 12,000 RPM motors; height adjustment with the top pressure beam and tilting range +/- 1°. Manually adjusted with digital counters. -- Multifunction Profile/Bevel/Corner Rounding Unit:Multifunction (2) 0.4 kW (0.54 HP) - 12,000 RPM Motors to fine trim the edge overhangs at the workpiece upper & lower edge, as well as trimming around the front & rear vertical edge; Servo controlled.Max. feed speed 0f 20 MPM (65.6 FPM) when corner rounding. -- Profile/Bevel Scraping Unit:Top & bottom for thick PVC/ABS, pneumatically activated. -- Flat Glue Scraper Unit:Top & bottom, pneumatically activated to remove potential glue squeeze-out. -- Buffing Unit:Top & bottom edge buffing/polishing.

HOMAG AMBITION 2262 (KAL 210) PRODUCTION EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): + LIGMATECH Return ConveyorSpecifications: -- Working Capacity: Coiled stock min/max Edge thickness 0.4 - 3 mm (0.016. - 0.118"), Panel stock min/max thickness 12 - 40 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18"). -- In-feed Fence:Adjustable in-feed fence with manual digital indicator positioning. -- Pre-Milling Station:Two 3.0 kW (4.0 HP), 150 Hz, 9,000 RPM Motors; equipped with trimming column, (2) horizontal and cross slides with spindle adjustment, electro-pneumatic horizontal jump movement of the first motor; includes electronic frequency inverter for control of motor speed and braking, two (2) dust extraction hoods, air jet panel blow-off device & SIKO digital counters for adjustments. -- Panel Pre-HeaterPre-heating the panel brings the panel to an appropriate temperature for better adhesion; this is especially beneficial in cooler temperatures.Quartz lamp for heating substrate edge before glue application improved edge quality and optimum bonding. -- Multi-Purpose Magazine:A multi-purpose 6-coil magazine expands capability by running coiled material.Magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panelon the edgeband. -- Gluing System: (EVA - Hot Melt)QA 34 - Quick Melt Overhead Unit & heated roller applicator digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allow for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gatesLower melting unit equipped with automatic glue level control. Melting capacity: 12 KG/h (26 LBS/h) -- Pressure Section:Manual Adjustment with digital counter, (1) large 160 mm dia. driven & (6) 70 mm dia idle rollers, pneumatic pressure control depending on edge banding material used.WORKSTATIONS: -- End Trimming Unit HL 81:0.8 kW (1.0 HP) x 2 - 200 Hz, 12,000 RPM Motors. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer 30 deg. to straight cut. -- Rough/Pre-Trimming Unit:Top & bottom, 0.55 kW (0.74 HP) x 2 - 12,000 RPM Motors; Height adjustment with the top pressure-beam and tilting range +/- 1°.Manually adjusted with digital counters. -- Profile/Bevel/Corner Rounding Unit FK 11:Multi function 0.4 kW (0.54 HP) x 2)- 12,000 RPM Motor to fine trim the edge overhangs at the work-piece upper & lower edge, as well as trimming around the front & rear vertical edge; Servo controlled, Max. feed speed 20 MPM (65.6 FPM). -- Profile/Bevel Scraping Unit:Top & bottom for thick PVC/ABS, pneumatically activated. -- Flat Glue Scraper Unit:Top & bottom, pneumatically activated to remove potential glue squeeze-out. -- Buffing Unit:Top & bottom edge buffing/polishing. -- Spraying Units:Top/Bottom spraying device is designed for applying a separating agent, for easier cleaning of any residual

HOMAG AMBITION 2274 (KAL 370/6/A3) EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Working Capacity: Coiled stock min/max Edge thickness 0.3 - 3 mm (0.011. - 0.118"), Strip material min/max Edge Thickness 0.4 - 1 mm (0.016 - 0.039"),Panel stock min/max thickness 8 - 60 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18").Minimum workpiece width: 2.36" (60 mm) with workpiece thickness ≤ 22 mm) & 4.13" (105 mm) with workpiece thickness > 22 mm). -- Cleaning Agent Spraying Units:Top/Bottom spraying device prior to workpiece pre-milling. Designed for applying a separating agent, for easier cleaning of any residual glue on the panel. -- In-Feed Fence: Pre-heated manually adjustable in-feed fence with digital indicators. -- Pre-Milling Station:(2) 2.2 HP (3.0 kW) - 150 Hz, 9,000 RPM vertical jointing spindle motors; equipped with panel blow-off device and SIKO digital counters for adjustments. -- Panel Pre-Heat Unit: Quartz lamp for heating substrate edge before glue application. -- Edge Magazine:A multi-purpose 2-coil magazine expands capability by running coiled material & strips. Maximum roll diameter: 400 mm & 830 mm.Magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panelon the edgebanding. -- Gluing System Homag Quickmelt: QA 3 - Quick Melt Overhead Unit & heated roller applicator digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allows for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gatesLower melting unit equipped with automatic glue level control. Melting capacity: 12 kG/Hr (26 Lbs/Hr). Ultra-fast five-minute (5) heat-up time. -- Pressure Section: Programmable (Servo), automatic pressure zone adjustment, (1) large 150 mm dia. driven & (4) 70 mm dia. idle rollers, pneumatic pressure control depending on edgebanding material used.Workstations: -- End Trimming Unit:(2) 1 HP (0.8 kW) - 200 Hz, 12,000 RPM Motor ea. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer to straight snip. Programmable (Servo). -- Rough/Pre-Trimming Unit:(2) 0.55 kW 0.74 HP (0.55 kW) - 12,000 RPM Motors, tilting range +/- 1° & counter-rotating to machine feed to prevent blowout & .Height adjustment synchronized with the top pressure-beam .With digital counters. -- Profile/Bevel/Corner Rounding Unit:(2) 0.54 HP ( 0.4 kW) - 12,000 RPM, Multi-function Motors to fine trim the edge overhangs at the work-piece upper & lower edge, as well as trimming around the front & rear vertical edge.By way of the machine control, this unit adjusts between a radius and a chamfer without a tooling change.Max. feed speed 20 MPM (65.6 FPM) when using "Corner Rounding Unit". -- Profile/Bevel Scraping Unit:Top & bottom for thick PVC/ABS, electro-pneumatic positioning & pneumatically activated. Pneumatically-controlled