This line is for sale as one lot. 1. Vertical Reciprocating Conveyor (VRC) - 106x80x72 - Roller Dimensions: 94x3 inch diameter - 72" wide roller deck 2. Chain Transfer Conveyor - Space between rollers is 4 feet (size of Transfer deck) - Rollers on each side measure 94x3. - Roller housings on each side measure 72x96x26. -Total dimensions: 72x224x26. 3. Straight chain driven Conveyor - 72x100x26 - 8' rollers 4. 360° rotating turntable conveyor -Base dimensions: 74x58 -Roller dimensions: 40x3 - Conveyor Dimensions: 72x48x26 5. Straight belt driven conveyors (4 of them) - 54x12x12 belts not included 6. Curved belt driven Conveyor - Exterior curve: 224x48x26 - Rollers are 40" long and vary from 2-4.5" wide along curve. 7. Line conveyors (2) - 144x36x24 - Rollers available for this 8. Stacked rollers -96x66x75 - Roller dimensions: 80x3 9. Straight Gravity Rollers (18 of them) - 148x36x6.25 These rollers were stacked 4 high. Legs are available to stack them or they will work in line. 222' run consisting of 18 pieces. 10. 32' decline belt conveyor - This has damage. See last photo.

Each system is custom built to fit your specifications. Standard Electric Lateral Chain Feeders include Basic Feeder with transport length of 30" Workpiece width 3/4" - 9-1/4" Min. Workpiece length 12" Drive system with 4 HP total drive system Feed speed range 50 - 250 ft/min (up to 400ft/min available) Thickness 1/4" - 4" Steel flat top chain 60 Cycle per minute Adjustable Fence 35MM Feed Wheel Shafts Options 6'-16' Lateral Chain Feeder Feed Wheel Knurled, Urethane or Light Knurl Hub Options 3/4" or 2" Powder Coating Bridge Side Fence Feed Speeds up to 400 FPM Short Stock Fence 12" Wide Capacty

This line will produce 4-5 bags per minute. Outfeed conveyor from each line Optional: Infeed auger and shaving bin

60" Pallet DIsmantler Motor 10 HP, 220/440V, 3 phase Switch on/off Band saw 228” long x 1-1/4” wide Table dimensions: 60” width x 48” depth Maximum size pallet to dismantle: 60” wide x any length Maximum distance between the horizontal bandsaw blade from table: 1” and up to 3” if the table stop end is cut. Machine dimensions: 115” length X 52” width x 55” height Weight 1,050 lb.

Single Head Pallet Notcher - New with warranty! 7.5 HP Motor 220/440 3PH Maximum Notch Size: 9" x 2-1/2" x 1-5/8 Power switch with magnetic starter Cutterhead with 4-stright HSS knives (optional 40 knife cutterhead) Dimensions: 48" L x 36" W x 40" H

Northteck MRS-14-DXL 460v Manufacturer notes: This is a very popular machine and cost effective. New open ended design allows for you to cut wide material up to 27-1/8? wide. Plus spare arbors, lasers, and the optional quick locking, easy to adjust infeed will not break the bank. The Northtech heavy-duty 50 HP multi-rip (“gang-rip”) saw with 15? maximum blade diameter quickly and accurately cuts material up to 4-15/16? thick and 27-1/8” wide. Cutting both sides of your blanks at once provides incredible parallelism, reducing required moulder allowance, and increasing your yield. Laser guides (one included) and an optional 103” fence make proper alignment of even the longest material simple and precise. Variable feed speeds of 25 – 120 FPM and powered height adjustment further improve operator efficiency.

6” x 24” capacity 2 sided knives on helical cutter head 534 hours in meter

16 HP 12 filter bags up 4 collection bags lower Lots of pipe

- Close link chain vs. open (no dust or pinch point) - Oiler has twice the number of lube points (critical) - The VS adjustment location on the 14N. - Can cut up to 4 15/16? with 14? blade vs. the MRS-12 12? blade 3-15/16”. - Can run 12? as well on the MRS-14N - Bottom kickback fingers for added safety - Saws, with proper tooling and material, can glue line Specifications: - Main Motor Hp. = 50 Hp. - Voltage/ Freq. = 460 Volt 60Hz - Phase = 3 Phase - Amp Requirement = 35 Amps - Feed Hp. = 2 Speed 1.5 / 3 Hp. - Feed System = Feed Chain - Feed Speed = 25 – 120 FPM - Variable Speed = Variable Speed Pulley - Elevation Hp. = 1/4 Hp. - Elevation Style = Manual Wheel Adjustment - Elevation Sys. = Jack Screw / Linear Guides - Total Hp. = 53.25 Hp. - Electronics = CE Approved Components - Dual Voltage = Elevation Arbor Motors - Control Voltage = 110 Volt - Assisted Start = Wye-Delta - Pass-Line = 33-1/2” - Min. Length = 17-3/4” - Min. Width = 1/2” - Max. Width = 27-1/8” - Min. Thickness = 5/16” - Max. Thickness = 4-15/16” - Arbor Rpm = 3570 Rpm - Blade Size = 12” Tungsten Carbide Tipped - No. of Teeth = 36 Tooth - Blade Kerf = 3.5 mm - Cleaning System = Brush on Chain - Vertical Travel = 3/8” – 5” - Dust Collection = (2) 6” @ 1962 CFM - Arbor Diameter = 70 mm - Hold Down Style = Pressure Plate - Kickback Finger = (2) Top (1) Bottom Sets - Emergency Stop = Push Button - Rear E Stop = Push Button - Safety Feature = Safety Interlock Switch - Guarding = Full Cabinet Enclosure - Oiler = Automatic Mechanical Oiler - Low Oil Warning = Low Oil Shut-off - Fence Type = Adjustable - Fence Dims. = 103” Length - Frame Const. = 5/16” Steel Construction - Worktable Dims. = 27-1/8” x 64” - Infeed Table = 13-3/4” x 103” - Decible Rating = 74 dB - Net Weight = 4402 Lbs. - Gross Weight = 4694 Lbs. - Machine Dims. = 67” x 58” x 71” - Packaging Dims = 72” x 65” x 77”

Nyle PHT350 Kiln System was powered up and tested, but not put into production.

Nyle Firewood Dry kiln No chamber included

Oakley Edge Sander

Ogden SL3660 RFS

Oliver 36" Band Resaw

Oliver Sawmill New Carriage Wheels New battery

Front/rear trim Top/bottom trim Top/bottom bevel Moulding Edgesanding

Single horizontal drill and dowel; 1300 mm work table with four fields; sure shot revolver system to guarantee the fastest cycle time, average one second, and extreme reliability; simple user friendly touch screen; heavy duty steel frame for maximum rigidity; large phenolic table with robust clamps suitable also for delicate materials; barcoding and ethernet ready; laser for measuring the part and populate the program;

3 Moulding heads 1 grooving head workpiece length 2300 mm workpiece thickness 35 mm Hopper feed Numeric controller

61" x 122" flat table Four (4) vacuum zones Suitable for nesting or use of pods or clamps Pneumatic reference pins and rails Drill unit 2 HP 4,500 RPM Nine (9) vertical spindles Router 12 HP Variable RPM, 1,000 - 22,000 Full torque at 9,000 RPM Full HP at 12,000 RPM HSK63F, quick-change Air-cooled Air blow-off nozzle Automatic tool changer Eight (8) position rotary Tool length touch probe Automatic unloading device with integrated dust collection PC control on mobile cart Windows operating system Standard keyboard and mouse Color, flat-screen monitor Fanuc OiM-F controller system Hand-held controller Fanuc drive system Dual drive, dual support for X axis Central lubrication system Dust shroud Photo eye safety barrier Like New – Used for less than a month

Omnitech Selexx Pal CNC Router