NOVY 1872V Multi Spindle Vertical Boring Machine 12 Spindles Vertical boring machineSpecifications: -- Table Hardwood 18" X 72' -- Table stroke 0"- 6" -- (12) Spindles in line at 5" center to center, spindle nose with 0" to 1/2" chuck -- (2) drive motor 2 HP with magnetic starter -- (4) Spring loaded hold down -- Savety guard -- Foot swtich

OAKLEY H-5 Double Sided Edge Sander. -- General Specs: With 7.5 HP -1,800 RPM TEFC motor; (2) 8-1/2" x 57-1/2" Cast Iron platens; 8" x 164" abrasive belt, 4,680 FPM belt speed. -- Equipped with: One 11" x 62" Cast iron side table on one side and (1) 19" x 64" cast table on the other side, (1) cast iron radius tilting end table, end table tilts 0 ° - 45°; 6" vertical table travel w/hand wheel adjustment. -- Features: Rubber covered direct drive pulley and idler pulley,Complete with: Magnetic starter with overload protection, (8) dead head radius ends with graphite covering, and (1) steel covered spare head roll.

OGAM - PO-340, ...Dip Chain Gang Rip Saw Specifications: -- 75 HP TEFC Motor, dip chain feed with overhead arbor. -- 4.3"; x 13.3"; Cut capacity. -- 16" Max. blade diameter. -- Power rise and fall. -- 70 mm dia. arbor. -- 2 HP Variable feed speed up to 115 FPM.Equipped with & Features: -- Automatic chain oiler. -- (3) Sets antikickback fingers. -- Adjustable infeed fence. -- Motor load meter. -- Many new saw blades.

OGAM MODEL PO-340 DIP CHAIN GANG RIPSAW ( THis is a Parts machine only )Specifications: -- 60 HP arbor motor, dip chain feed with overhead arbor, 13-3/8" (340 mm) max. rip cap. (between saw blades), 12-5/8" chain width. -- 9-13/16" Mn. to 13-7/8" max. blade dia., 4-3/4" max. depth of cut (manual raise and lower of the spindle), 70 mm dia. arbor runs @ 4,200 RPM; min. board length 19-3/4" (without short stock feed plate-see photo). -- Variable speed belted feed motor 20 to 100 FPM (approximate).Note From Seller: Ogam Gang Rip Saw. 60 HP motor 230/460. I don’t know much about this machine. Bought it used but haven’t been able to hook it up due to our current electrical service. The person I bought it from says it ran well when taken out of service. Can load on a truck.

OGAM PO/M Straight Line Rip Saw;Specifications: -- 20 HP Main motor. -- 24"; throat capacity. -- Max. cutting height: with 12" blade 3", with 16" blade 4". -- Min. diameter of circular saw blades: 8". -- Max. dia. of circular saw blades: 16". -- Min. length of working pieces: 10". -- Variable feed speed from 50 -154 Ft./minute. -- Feeding belt width: 11". -- Spindle Speed: 4,500 RPM. -- 36"; x 60"; table.Equipped with & Features: -- Fence and rail system with one stop. -- Infeed table row of anti-kick back fingers. -- Steel smooth top hold down roller. -- Top row of anti-kick back fingers. -- Steel smooth top hold down roller. -- Split hold down steel smooth roller around blade. -- Split hold down steel smooth roller around blade. -- Steel smooth top hold down roller. -- Chain is in excellent condition!

OLIVER 2019 Wood Turning Lathe;This lathe brings the lathe back to the OLIVER line, in true OLIVER Fashion! -- Starting with a solid, stable cast iron base, legs, bed, tool rest, and headstock. -- OLIVER adds a powerful reversible 2 HP motor with a wide speed range for a variety of tasks. -- A frequency inverter and RPM Digital Readout give you an accurate read on your speed so you can precisely adjust for any particular job.Specifications: -- 41" Between Centers, 18" Swing over bed, 40" Swing Outboard; -- Spindle Speed 200 - 2,400 RPM, Front Faceplates 6". (2).Features: -- One of the best features on the lathe is the In-board and Out-board headstocks (slides on the bed), enabling you to work on very large Bowls and most anything else you need to turn. The slide extension can increase the center distance to 57" with optional extension bed.Includes: -- Integral spindle index for (36) positions.Dimesniosn/Weight: 46.5"long x 19.5" depth x 49.25" height. Approx. 415Lbs.Available Options: -- Bed extension that mounts in two positions....Protective Safety Guard. Assembly.... Please call. -- See attached literature for more specifications.

20’ OLIVER LATHE – PATTERN MAKERS TURNING LATHESpecifications: -- 30" Swing over 20’ bed, 15"; clear from bed to center; 92" Swing outboard, 16’ between centers -- Belt-drive Step pulley, 4-Speed Step pulley -- Single geared tool rest to hand crank for traversing the length of lathe -- Head Stock Spindle dia. 1 – 7/8";, Tail Stock Spindle dia. -- Head Stock can be offset 10 degrees for tapered columns -- Cone dia. Steps – 5";, 7 – 3/8";, 9 – 5/8";, 12"; -- (8) Spindle speeds, 160 to 2,520 RPM

OLIVER 15" Planer with Helical Cutterhead - 10014, 3 HP (Single Phase)Unique design allows motor and cutter head to move in unison.Specifications: -- Auto-depth lock features twin nitrogen cylinders virtually eliminates snipping. -- Helical cutter head with premium carbide inserts. -- 4-Sided cutting inserts are indexed and easy to replace. -- Heavy cast iron construction including extension wings. -- Table and extensions wings are precision ground for smooth stock feeding. -- Table is fixed allowing easy use of auxiliary stock support. -- Wixey digital read-out allows precise thickness settings. -- Large handwheel and support struts allow easy height adjustment. -- Four-post design ensures head alignment regardless of stock thickness. -- Two-speed feed gearbox for better cuts, Oil bath gear lubrication for years of performance.Complete with: -- 4"; Port allows excellent dust management. -- Built-in mobile base allows easy movement in the shop. -- Magnetic switch for added protection and safety.

14" Max. blade cap., 2 HP motor, 1" dia. arbor tilts 0° - 45° via hand wheel; separate handwheel for raise and lower of the arbor. -- Includes: original miter gauge, counterweighted overhead blade guard, wrench. -- NOTE: Table and Biesemeyer Fence shown in photos have been sold and are not included with machine.

OLIVER - 299-D, ...24" Planer (8" thickness capacity) -- Capacity: 24" x 8" Thick planes stock as short as 11". -- 3-Knife steel cutterhead motor: -- 5 HP; 3 PH. -- Sectional infeed rolls: - (12) 2" Wide sections: Sectional chip breaker. -- (12) 2" Wide sections with: 1/4" Independent Lift. -- (2) Driven bed rolls; feed motor: 1 HP - 3 PH REEVES Variable speed 15 - 60 FPM.

OLIVER 299-D Single Surface Planer;24" Width x 8" thickness cap., Cabinet Planer; -- 5 HP Cutter-head motor, and equipped with a straight knife cutter-head. -- 2 HP Gear box variable speed feed works with speeds of 15 - 60 FPM; sectional feed rolls, sectional chip breakers. -- Complete with: Knife grinding equipment for OLIVER carbide cutter-head, knife setting device, top dust hood, quick set adjustment on bed rollers.One of the "Original" OLIVER Planers!

QUICK L-HLPP-2-20-43-8-12 ...2-Sided Hydraulic Laminating Press: -- Number of working sections: (2) -- Working width, section #1: 6" and 8" -- Working width, section #2: 8", 10"; and 12" -- Maximum working length: 6,200mm (20.3') -- Maximum working height: 1,100mm (43.3") -- Pressure at the glue line: Up to 175 PSIMain Laminating Cylinders: -- Number of cylinders, section #1: (14) -- Number of cylinders, section #2: (21) -- Size of cylinders: 100 mm dia. x 80 mm strokeHolddown Cylinders: -- Number of cylinders, section #1: (14) -- Number of cylinders, section #2: (21) -- Size of cylinders: 40 mm dia. x 150 mm strokeLift Cylinders: -- Number of cylinders: (2) on each side = (4) -- Size of cylinders: 63 mm dia.Hydraulic Pump: -- Drive motor: 10 HP -- Maximum pressure: 140 kG/cm² -- Maximum Holddown Cylinder Pressure: 50 kG/cm² -- Maximum Side Lift Cylinder Pressure: 50 kG/cm² -- Shipped without hydraulic oil in the oil tank

QUICKWOOD CD2-300 Moulding & Profile Sander or Denibber;4-Head Brush Loading Sander, 12" width and 4" height cap., for 3-sided sanding & denibbing. Head Configuration: -- (2) "BH300" Overhead rotating abrasive/brush heads, both arbors equipped with a combination of abrasive and brush loadings, 12" long arbors, 12" max. dia. sanding discs. -- 0.75 HP Motor drives each arbor with inverter for 200 - 1,200 RPM arbor rotation speed. -- Right & Left ("BH-140" & "BH-100" respectively) side mounted rotating abrasive/brush heads. -- Tilting heads and adjustable in-and-out, 6" long arbor, 8" dia. sanding discs, 0.5 HP motor each head. -- 0" - 4" Max. manual part height adjustment via hand wheel; 57-1/2" long roller conveyor with PVC covered rollers, variable feed speed 10 - 60 FPM. -- Infeed & outfeed overhead holddown rolls and (1) between the top heads. Includes centralized control panel, hubs, abrasive, & brush. -- Can also be ordered with just (2) top heads or (3) heads, ie. Left or Right. Call for separate prices.

QUINCY - QMT15 ACA, ...Air Compressor (Rotary Screw) w/DryerSpecifications: -- 15 HP - 54.9 CFM @ 125 PSIG; 120-Gallon tank mounted with Refrigerated Dryer & Filters. Equipped with: -- 15 HP TEFC Motor; air-cooled aftercooler; high efficiency inlet filter; upward package air discharge; vibration isolation; Wye-Delta start. -- 54.9 CFM @ 125 PSIG; 69 dBA; 120-gal horizontal tank; refrigerated air dryer.Total operating hours: (29,407).Specifications subject to verification

QUINCY "QSV-40" 40 HP vacuum pump:550 ACFM, 29.9"HgV, Direct drive rotary screw vacuum, positive lubrication fluid pump. -- Equipped with:Modulating inlet valve, temperature regulating valve, and high discharge temperature shutdown system with manual reset. -- Complete with:Complete unit enclosure, gauges, exhaust separation system, spin-on fluid filter, and magnetic motor starter -- Additional:All service records from date of purchase. -- Quincy the OEM did 1 partial and 1 full tune up every year since purchase.

QUINCY QSVB-25ANN2C Vacuum Pump:25 HP "QSVB Series", 371 CFM, 29.9"HgV rotary screw vacuum, positive lubrication fluid pump; 3″ inlet and 2″ exhaust port.. -- Equipped with:Modulating inlet valve, temperature regulating valve, and high discharge temperature shutdown system with manual reset. -- Complete with:Control panel, electrical enclosure, gauges, exhaust separation system, spin-on fluid filter, and magnetic motor starter. NOTE: The pump only has 969.2 total hours on the meter

RADER - Trailer Dumper with 30 ft. Tipping DeckComes with the following components and features: -- This unit was installed at the current location in approx. 1971 and is reportedly in great working order and condition. -- Previously used for Dumping Wood Chip Trailers. -- Professional rigging and loading is available. Decks are often extended for longer (53 ft.) trailers.

RAIMANN Model ASA 1650, Veneer Patcher.Specifications: -- 61" Throat cap., 3 HP gear motor with new/rebuilt drive unit, strip type mechanical plug-feeder mechanism - cap. of up to (40) plugs/Min.; -- Thickness of veneer patchable 1/32" - 1/5" (0.08 mm - 0.2 mm) (softwoods), 1/20" - 3/16" (hardwoods). P-34 dies. -- Tool sequence: Veneer patch is cut by the table die and scrap is ejected into discharge chutes, veneer patch blank is then positioned against the underside of the table die, plug punch cuts replacement veneer patch from underside and patch is inserted into the proper position. -- Reconditioned by experts. -- Overall size: 10' 8" (3,250 mm) Length x 67" (1,700 mm) height; approx. weight 12,000 Lbs (5,450 kG). -- Optional Glue applicator add ...$9,975. -- Optional strip feeder add ...$6,750.Actual model is RAIMANN Model ASA 1650

RAIMANN - KM-310, ...Gang (Multi-Blade) Rip Saw12-1/4" Max. width cap., 13-1/2" chain width, 50 HP - 4,200 RPM V-belt driven arbor.Features: -- "Quickfix Hydro-Quick" Arbor: Multiple Saw blades are mounted on the arbor, they slide up-and-down the arbor into position and lock into place by tightening the end of the arbor; no tools & no spacers required. -- Frequency controlled feed speed of 13 - 110 FPM, 2.2 HP feed drive, chain spikes every 3rd chain link, automatic chain lubrication.Specifications: -- 300 mm (11.8") Max. saw blade dia. with 80 mm (3.15") bore, 65 mm (2.55") dia. arbor. -- Provides 3" max. depth of cut with pressure shoe, 3-1/2" depth of cut without. -- Manual thickness adjustment of upper holddown rolls with indicator scale. -- 6" Throat depth to the right of blade; 7/8" min. strip width, 17-3/4" min. stock length.Equipped with: -- (4) Sets of top & bottom antikickback fingers. -- Extended infeed with additional bed roll, and adjustable infeed fence. -- Motor load meters and automatic STAR DELTA starting. -- Automatic over thickness shutoff on infeed and 7-1/4" dia. dust hood. -- (4) Laser lights.Also included: -- (6) Used blades.

RAIMANN - KM-310, ...Gang (Multi-Blade) Rip Saw12-1/4" Max. width cap., 13-1/2" chain width, 50 HP - 4,200 RPM V-belt driven arbor.Features: -- "Quickfix Hydro-Quick" Arbor: Multiple Saw blades are mounted on the arbor, they slide up-and-down the arbor into position and lock into place by tightening the end of the arbor; no tools & no spacers required. -- Frequency controlled feed speed of 13 - 110 FPM, 2.2 HP feed drive, chain spikes every 3rd chain link, automatic chain lubrication.Specifications: -- 300 mm (11.8") Max. saw blade dia. with 80 mm (3.15") bore, 65 mm (2.55") dia. arbor. -- Provides 3" max. depth of cut with pressure shoe, 3-1/2" depth of cut without. -- Manual thickness adjustment of upper holddown rolls with indicator scale. -- 6" Throat depth to the right of blade; 7/8" min. strip width, 17-3/4" min. stock length.Equipped with: -- (4) Sets of top & bottom antikickback fingers. -- Extended infeed with additional bed roll, and adjustable infeed fence. -- Motor load meters and automatic STAR DELTA starting. -- Automatic over thickness shutoff on infeed and 7-1/4" dia. dust hood.