CAM-WOOD 16' Pusher Type Cutoff Saw with Crayon Marking connected to a CAM-WOOD 12" wide End Matcher; System width capacity is 12" with a maximum inbound board length of 16' (as priced here). 8' and 12' Saws are also available. Call Jeff for price deduction.General Data: -- Cut-Off Saw is arranged to remove defects from Clear. Will chop for random length clear material OR optimize clear wood according to your cutlist, delivering either to the End Matcher. -- The line requires (1) man to mark and feed the Cutoff Saw and (1) man to offbear and stack finished work coming from the End Matcher. Price includes the following equipment and specifications: Defect Saw Features: -- 18" CAM-WOOD Model CS-18AAT-16' Automatic Cut Off Saw equipped with Automatic Pusher for increased automation and efficiency -- 16' Infeed table -- Works as an automatic pusher for defect removal and fixed length cutting when crayon marking -- PLC controlled automatic pusher device is driven by servo motor at feed speeds up to 200 FPMAutomatic Pusher Operation: -- Operator places crayon marks at the leading and trailing ends of a defect or waste zone (Optional) -- Pusher moves the board to the first crayon marked defect, automatically completes the cutting cycle, and continues to position and chop the board at each crayon mark, thereby removing all waste zones. When the board is finished, the pusher returns to its starting position at top speed and starts on the next board -- Super Pusher travels up to 200 FPM -- Sealed, long-life ball bearings -- Precision ground cast iron table with heavy metal stand -- Easy to operate in all operations -- Saw blade comes up from beneath the table and returns after cutting for safe operation -- Totally enclosed blade guard prevents danger during cutting cycle -- Includes magnetic starters with overload protectionCutting & Other Specifications: -- (45) Strokes/Min -- 18"; Saw Blade Diameter with 1"; Saw Arbor -- 10 HP Arbor Motor -- 3,200 RPM Blade Speed -- 90 PSI Compressed Air requirement with 1" Inlet -- (1) 4"; Dust Hood -- Machine Size (W x L), 30" X 28-1/2'Automatic Transfer between Defect Saw and End MatcherCAM-WOOD SFJ -300 End Matcher with the following Specifications: -- Machines tongue and groove at ends of random or fixed length boards as provided by the Defect Saw -- Includes powered conveyor for infeed and steel landing table at the outfeed -- Air operated hold downs keep material firmly in place during the machining process -- Cutter heads move in and out while cutting a tongue on the trailing end of one part and a groove on the leading end of the following pieceFeatures: -- PLC controls combined with touch-screen for maximum convenience of operation -- Each cutter head is powered by a separate motor driving the spindles at 7,500 RPM -- Accepts unlimited wood lengths via an automated conveyor for infeed and outfeed -- Cutterhead travel thru the wood is controlled by a VFD which permits automatic speed changes to suit various

CAM-WOOD CS-650SCC Double End Matcher For Herringbone and Chevron FlooringNC Controlled Trough Feed Type End Matcher for Chevron and Herringbone flooringSpecifications: -- Working Width 1-1/2"; to 6"; -- Working Thickness 1/2"; to 1"; -- Working Length 8"; to 50"; -- Feed Speed 70 FPM with inverter -- Cycle time can be 4 to 8 second per piece1st Saw Station: -- Saw Blade Diameter 10"; -- Saw Motor 7-1/2 HP -- Feed Motor 1 HP with Gear Reducer & Inverter. -- Auto Stop & Align2nd Feeding Station: -- Feed Motor 1 HP with Gear Reducer & Inverter. -- Auto Stop & Align3rd Tennon Station: -- High Frequency HSD Routers with HSK63 Spindle, 11 kW (15 HP) x 2 units -- Forward and Reversed Direction at each spindle. -- Feed Motor 1 HP with Gear Reducer & Inverter. -- Auto Stop & AlignFeatures: -- Special Design CHEVRON & HERRINGBONE Double End Tenoner -- Servo control for 45° and 90° cutting. -- The automatic high-speed through feed device allows for perfect finishing at speeds ranging from 45 ~ 70 FPM by inverter -- Suitable for mass production of woodworking factory for processing of double-end cutting, tenoning, grooving, moulding, and sanding. -- Scoring Saw, Trim Saw, Jump Coping shaper, and Coping Shaper: Total 4 stations at each side. -- HMI plus PLC controller for easy setting and operation. -- It is a powerful machine great for heavy-duty production. -- In addition to the double-end cutting, all the settings and other processing can also be executed with high accuracy. -- The specially designed numeric controller allows quick setting of sizes for tolerance within 0.004";. -- Variable speed, through feed, wide rubber pad, spring-loaded dogs conveyor for the best finish selections. -- Heavy-duty pressure rolls at top of a wide conveyor to hold the material tight to prevent sliding during the cutting process. -- Shaper heads can be adjusted to move up & down, forward & backward. -- Features industrial motors for full power cutting capacity.Optional equipment: -- Total sound enclosure add: ...$ 7,900 -- Infeed magazine add ...$ 4,900

CAM-WOOD EB-K7PMX EDGEBANDER (W/PRE-MILLING): -- Specifications:0.4 mm - 3 mm Max. edge thickness cap., 10 mm - 60 mm (0.75" - 2.36") panel thickness cap. -- Minimum panel dimensions 160 mm long x 88.9 mm wide (6.3" x 3.5"). -- Automatic feed of coil banding and semi-automatic strip fed magazine (strips 1- 3 mm max.) with 3 mm PVC cap. guillotine.Infeed Section: -- Pre-Mill Unit with: (2) 3 HP (2.25 kW) -12,000 RPM High Frequency motors. -- Feeding of edging by strip or coil is automatic and synchronous with panel feed. -- Gluing Unit: Roller driven by a 1 HP (0.75 KW) motor; Tank heating 2.3 kW. -- Guillotine to cut edgebanding in coils up to 3 mm thick. -- Pneumatically controlled side pressure section with (3) pressure rollers; 1st synchronously driven, (2) idlers; Independent adjustment for straight edge banding.Workstations: -- Double Motor end trimming saw unit with (2) 1 HP (0.75 kW) - 12,000 RPM High-Frequency motors. -- Cutting group moves on ways made of hardened steel, to guarantee high precision and reliability. -- Rough Top & Bottom Trim station with (2) 0.75 HP (0.56 kW) - 12,000 RPM Independent High Frequency motors; unit features adjustable copying on vertical & horizontal floating movements, adjustable cutter-head position by mechanical digital readouts, quick release (electrical & mechanical). -- Fine Top & Bottom Trim station with (2) 0.75 HP (0.56 kW) - 12,000 RPM. -- Top & Bottom Profile Scraper station with quick working or exclusion setting of both top & bottom units, micrometer adjustment; features thick chrome plated copying shoes. -- Top & Bottom Buffing/Polishing unit with (2) 0.25 HP (0.18 kW) - 1,400 RPM motors.Feed System & Features: -- 25 - 60 FPM feed speed powered by 2 HP (1.5 kW) gear motor. -- Feed chain pads with precision ground round guides to ensure precise linear tracking of the workpiece. Replaceable rubberized surface inserts. -- Rubberized hold-down rollers with ball bearings for low friction and long life. -- Complete with: Sound / Safety covers for all work units with all required dust extraction outlets. Heavy, robust construction to eliminate vibration and ensure accuracy and stability.Includes: Outrigger support for wider work pieces. -- Owner’s Manual with mechanical & electrical schematics and parts breakdown; covered by a 1-Year Factory Warranty on parts. -- Total machine power is 11 kW. Transformers are available at additional cost to convert to desired alternate voltage requirements.

CAM-WOOD EB-L5 EDGEBANDER0.4 mm - 3 mm Edgebanding thickness capacity, 10 mm (3/8") - 50 mm (1.96") material thickness capacity, 63.5 mm (2.5") minimum part width, 160 mm (6.3") minimum part length. Equipped with: -- Automatic feed of coil banding and semi-automatic strip fed magazine (strips 1- 3 mm max.) with 3 mm PVC cap. guillotine. -- Teflon coated glue pot w/fast (10 - 12) Min heat-up time; 4-liter capacity. -- Guillotine to cut edgebanding in coils up to 3 mm thick. -- Pneumatically controlled pressure section with (3) pressure rollers; 1st drive, (2) idle.Workstations: -- Double Motor end trimming saw unit with (2) 1 HP (0.75 kW) - 12,000 RPM High-Frequency motors. Cutting group moves on rounded ways made of hardened steel, to guarantee high precision and reliability; cutting movement from the top of the panel. -- Top & Bottom Trim station with: (2) 0.75 HP (0.56 kW) - 12,000 RPM High-Frequency motors; unit features adjustable copying on vertical & horizontal floating movements, adjustable cutterhead position by mechanical digital readouts, quick release (electrical & mechanical). Includes (2) 3 mm radius cutters. -- Top & Bottom Buffing unit with (2) 0.50 HP (0.37 kW) - 1,400 RPM motors. Feed & Holddown: -- Feed rate of 12 MPM (40 FPM); feed chain pads with replaceable rubberized surface inserts. -- Special design "track frame" to eliminate feed chain side-to-side movement after years of use. -- Rubberized holddown rollers with ball bearings for low friction and long life. -- Complete with: Sound enclosure protects the operator from noise and debris.

CAM-WOOD EB-L5PM EDGEBANDER (W/PRE-MILLING): -- Specifications:0.4 mm - 3 mm Max. edge thickness cap., 10 mm - 50 mm (0.75" - 2") panel thickness cap. (when edgebanding 3 mm PVC max. thickness is 40 mm). -- Minimum panel dimensions 63.5 mm wide x 160 mm long (2.5" x 6.3"). -- Automatic feed of coil banding and semi-automatic strip fed magazine (strips 1- 3 mm max.) with 3 mm PVC cap. guillotine.Infeed Section: -- Pre-Mill Unit with: (2) 3 HP (2.25 kW) -12,000 RPM High Frequency motors. -- Feeding of edging by strip or coil is automatic and synchronous with panel feed. -- Gluing Unit: Roller driven by a 1 HP (0.75 KW) motor; Tank heating 2.3 kW. -- Guillotine to cut edgebanding in coils up to 3 mm thick. -- Pneumatically controlled side pressure section with (3) pressure rollers; 1st synchronously driven, (2) idlers; Independent adjustment for straight edge banding.Workstations: -- Double Motor end trimming saw unit with (2) 1 HP (0.75 kW) - 12,000 RPM High-Frequency motors. -- Cutting group moves on ways made of hardened steel, to guarantee high precision and reliability. -- Rough Top & Bottom Trim station with (2) 0.75 HP (0.56 kW) - 12,000 RPM Independent High Frequency motors; unit features adjustable copying on vertical & horizontal floating movements, adjustable cutterhead position by mechanical digital readouts, quick release (electrical & mechanical). -- Fine Top & Bottom Trim station with (2) 0.75 HP (0.56 kW) - 12,000 RPM -- Top & Bottom Scraper station with quick working or exclusion setting of both top & bottom units, micrometer adjustment; features thick chrome plated copying shoes. -- Top & Bottom Buffing/Polishing unit with (2) 0.25 HP (0.18 kW) - 1,400 RPM motors.Feed System & Features: -- 25 - 60 FPM feed speed powered by 2 HP (1.5 kW) gearmotor. -- Feed chain pads with precision ground round guides to ensure precise linear tracking of the workpiece. Replaceable rubberized surface inserts. -- Rubberized hold-down rollers with ball bearings for low friction and long life. -- Complete with: Sound / Safety covers for all work units with all required dust extraction outlets. Heavy, robust construction to eliminate vibration and ensures accuracy and stability.Includes: Outrigger support for wider workpieces. -- Owner’s Manual with mechanical & electrical schematics and parts breakdown; covered by a 1-Year Factory Warranty on parts. -- Total machine power is 11 kW. Transformers are available at an added cost to convert to desired alternate voltage requirement.

CAROLINA BLOWER 45-6 Standard Duty Fan/Motor package assembled complete 30 HP motor. -- Rated at 8,860 CFM at 10" SP. Fan inlet diameter is 19". -- Fabricated with 3/8" thick wheel blades, 1/4" thick housing, primed and painted beige. 30 HP TEFC motor. Unitary base, V-belt drives, shaft, and belt safety guards. -- This is an Industrial Material Handling fan with paddle-wheel construction. Also available in Heavy Duty version at extra cost, with thicker scroll-housing to handle airborne smaller solid wood or similar material.

Set of (3) Bins: (2) CAROTHERS-20 UNIT and (1) WEST COAST SHEET METAL- 15 UNIT with (2) Cyclones and One Hydraulic Power Pack...20 Unit CAROTHERS Shavings stores about 4,000 cu. ft. and 15 Unit Chip WCSM stores about 3,000 cu. ft. -- the (2) CAROTHERS Units share one 8' dia. Cyclone with levelling auger and the WCSM has separate 8' dia. Cyclone. Only (1) hydraulic Power pack is included. -- Rapid Powered Discharge Bin, prefabricated for nut & bolt erection, exterior constructed of 12-gauge structurally reinforced steel. -- Chips are discharged by a set of hydraulically operated clam-shell type bottom doors for approx. 78" x 144" free fall opening, opening & closing via (2) approx. 6.5" dia. double acting hydraulic cylinders w/stroke of approx. 48", Approx. 5 HP hydraulic pump motor with reservoir; braced, wide flange steel beam support structure with approx. 14' truck height clearance. -- Complete with: Operator's platform, upper catwalk w/handrail & (1) caged ladder and full w/ribbed sheet metal enclosure with truck size access door. -- Price for complete system includes dismantling and loading.

CAS (COMPRESSED AIR SYSTEMS) B73H84-E Reciprocating Air CompressorElite Series 7.5 HP 80 Gallon Horizontal Compressor @ 175 PSI / 24 CFMFeatures & Specifications: -- Access to Compressor Valves without Compressor Head Removal. -- All UL Electrical Controls -- ASME Tested Powder Coated Steel Tank. -- Auto Start / Stop. -- Bearings on Both Ends of the Crank Shaft. -- Centrifugal Unloader. -- Disk and Spring Valves. -- Fully Enclosed Belt Guard. -- Heavy-Duty Air Filter. -- Heavy-Duty (2) Stage Solid Cast Iron Pump. -- Industrial Grade Electric Motor. -- Magnetic Starter Mounted and Wired. -- Needle Bearings, and Inserts on Rods. -- Stainless Steel Flex Air Lines. -- Swedish Steel Valves. -- TEFC Drive Motor (3 Phase Only). -- Torrington Needle Bearings. -- 2-Grove B Width Motor Pulley. -- 2-Piece Tank Top Plate Design.Elite Compressor Features: -- All Basic Features. -- Automatic Tank Drain. -- Belt Guard After Cooler. -- Low Oil Monitor. -- Tank Discharge Ball Valve. -- Vibration Pads.

CASADEI ALA 23 EDGEBANDER WITH CORNER ROUNDING0.4 - 15 mm (1/2") Edge cap., panel thickness 10 to 60 mm (.39" to 2.36"). Minimum panel length 120 mm (4-3/4") and 55 mm (2-1/8") minimum width. Equipped with: -- Quick heat-up glue system,(approx. 12 Min) 1.5 Kg glue pot capacity. -- Pressure roll section with (3) rolls - one driven. Pneumatic cut-off guillotine.Workstations: -- Double end trim, chamfers 0° - 15° -- Top & bottom flush/radius trim, bevels 0° - 15°. -- Double motor Corner Rounding station -- Top & bottom scraping for 3 mm radius, -- Top & bottom buffing (0.25 HP - 2,800 RPM motors).NOTE: Seller states that the buffing unit appears to have an electrical issue and is not currently being used by the current owner";Actual Model: "ALA 23 R"

CASADEI FLEXA 47 RMA8 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING):Specifications: -- 0.4 mm - 3 mm Max. edge thickness cap., (0.5 mm to 3 mm for solid strip edge thickness). 8 mm - 50 mm (0.3" - 1.97") panel thickness cap. (when edgebanding 3 mm PVC max. thickness is 40 mm). -- Minimum panel dimensions 80 mm wide x 140 mm long (3.15" x 5.5"). -- Automatic feed of coil banding and semi-automatic strip fed magazine (strips 1- 3 mm max.) with 3 mm PVC cap. guillotine.Equipped with: -- Teflon coated glue pot w/fast (10 - 12) Min heat-up time; 1 Kg. capacity. -- Guillotine to cut edgebanding in coils up to 3 mm thick. -- Pneumatically controlled pressure section with (3) pressure rollers; 1st drive, (2) idle.Workstations: -- Pre-milling unit with 3 HP - 8,300 RPM High Frequency motors. -- Cutting group moves on rounded ways made of hardened steel, to guarantee high precision and reliability; cutting movement from the top of the panel is synchronized by the PLC control. -- Single motor, double-end trimming saw unit with (1) 0.25 HP - 12,000 RPM High Frequency motor. -- Top & Bottom Trim station with (2) 0.45 HP - 12,000 RPM High-Frequency motors; unit features adjustable copying on vertical & horizontal floating movements, adjustable cutter-head position by mechanical digital readouts, quick release (electrical & mechanical). -- Includes (2) 3 mm radius cutters. -- Corner Rounding Unit: 2-Motor Corner Rounding unit for leading & trailing edges. -- Top & Bottom 3 mm scrape station -- Top & Bottom Buffing unit with (2) 0.20 HP - 1,400 RPM motors. -- Fixed feed speed 23 FPM. -- Actual Model is CASADEI FLEXA 47 RMA8

CASADEI RANGER MC 3012 CNC MACHINING CENTER (VERTICAL, W/ATC): -- Specifications: Flexible "Vertical" Machining Center reaches movement speeds of 131 FPM (40 MPM) in X-axis, 98 FPM (30 MPM) in Y-axis, & 66 FPM (20 MPM) in Z-axis. -- Work Capacity:Max. part size for: X-Axis is 118" (3,000 mm); Y-axis 47.2" (1,200 mm); max. part thickness 3.9" (100 mm). -- Worktable:Vertical Phenolic MATRIX Grid table with: (5) Adjustable "tubeless" pneumatic locking panel supports, (3) adjustable vacuum pods per support.Pop Up Pneumatic backstops & pneumatic side stops for material positioning on the LH or RH side of the machine for mirror imaging. -- Boring Unit:(1) Boring block with: 2.25 HP (1.7 kW) - 4,000 RPM Motor.(10) Vertical spindles with: (5) Spindles in X-axis & (5) spindles in Y-axis.(6) Horizontal spindles with (2 + 2) in X-axis & (1 + 1) horizontal spindle in Y-axis.(1) X-Axis grooving saw: 5,000 RPM; for max. 120 mm dia. saw blade. -- Machining:(1) 6.7 HP (5 kW) Router with: ISO 30 Adaptor, variable speed from 1,000 - 18,000 RPM.(1) 5-Position ATC rack mounted on the side of the working unit. -- Operator & Machine Control:CNi PC Front End + Windows "XP" Operating System; 17" LCD, TFT monitor; international keyboard, soft touch keypad & industrial mouse; RS-232 Serial ports, USB ports; Ethernet connection.Real-time multitask processing; programs can be transferred via USB or downloading by wire is possible. -- Complete with:(1) 100 CBM/Hr BECKER Vacuum Pump; sound enclosure & perimeter safety devices. -- Actual Model is: CASADEI - RANGER MC 3012.

CASTALY - MAX370P, ...Edgebander with Premilling & Corner RoundingEdge thickness cap.: 0.4 - 3 mm; panel thickness: 8 - 45 mm; min. panel width: 100 mm (4″); min. panel length: 170 mm (6.7″).Equipped with: -- Quick melt Teflon coated glue pot; 2-1/2 Lbs cap; (2) spring-loaded pressure rollers (1 driven, 1 idling).PVC/ABS Automatic coil feed: 3 mm Max; thick, pneumatically operated guillotine; laminate strip material can be hand-fed; PLC Control System with: LED display & keypad.Workstations: -- Premill station with: (2) 1.1 kW - 12,000 RPM trim motors; 32 mm (1-1/4") max. material thickness. -- Single motor front & rear edge trim station. -- Top & Bottom trim station with: Insert knife cutters for radius trimming & bevel trimming. -- Corner Rounding Unit: Leading & trailing corners; (1) 1/2 HP (0.37 kW) - 12,000 RPM motor. -- Top & Bottom scrape station: 2 mm Radius. -- Top & Bottom buffing. -- Feed speed: 29 FPM.

CATERPILLAR- XQ125, ...100KW DIESEL GENERATOROnly 50 hours!Specifications: --Diesel Generator --HP/KW: 100 kW --Caterpillar Model: XQ125 --Model Year: 2020 --Hours: 55 --Frequency: 60 Hz --XQ125 - C4.4 engine. --Rating - 125 KVA, --100 KW prime, 60 Hertz, 3 Phase, 12 wire.

CEFLA TNS 6000 Rubber Belt Transfer Conveyor 236"; long x 74 1/4"; wide (66"; wide belt) -- 3PH motor --Adjustable height feet

CEFLA PSP6 Six (6) Gun Automatic Molding SprayerThe machine was purchased to spray PVC extrusions but the client changed his requirements, so the machine was taken from service. The machine has less than 1 year of light use and is in very good condition.As with all sprayers, it will require some cleaning and we recommend replacing the fluid lines with new ones. The machine has two (2) Spray zones with (3) guns in each. Each zone has a separate circuit. This machine is manufactured in the USA at the CEFLA facility in Charlotte, NC. Specifications: -- Two (2) Circuits Three (3) plus Three (3) or Six (6) on a single circuit -- ATEX Drive Motor, Inverter Controlled -- In / Outfeed Belts with Rollers with protection sleeves inside the spray booth -- ATEX-rated sensor-controlled guy triggers, individual on/off for all guns with individual manual test triggers -- Manual Atomization Controls -- ATEX-rated door safety switches -- Control Panel with Color Touch Screen -- One (1) 2000 CFM Exhaust, Explosion Proof -- Stainless Steel internal construction -- Pull out the overspray collection cart with removable Teflon-coated collection trays for ease of cleanup and the possibility of recuperation of coating material -- Filter cabinet on the back of the machine with easily replaceable mesh filters.

CEHISA PRO 10 .EDGEBANDER (W/PREMILL): -- Features: Pre-milling Station with: 2 x 1.5 kW (2.0 HP) 12,000 RPM motors; standard equipped with diamond cutters. Both spindles pneumatically controlled. -- Automatic Edge Magazine: For coiled material up to 3 mm thickness, strip feed magazine for up to 5 mm (3/16") solid wood banding. -- Quick Melt Glue System: 10 - 15 Min. heat up time, auto-temperature drop. Glue Tank is coated with nonstick material, quick change mechanism for easy maintenance and/or color change. -- Pressure Section: (1) Large dia. driven and (2) idle rollers. Digital readout and pneumatic positioning selectable from controller touchscreen. -- Edgebanding Workstations. End Trimming Station: Double motor front & rear, 2 x 0.35 kW (0.5 HP) - 12,000 RPM. -- Edge Trimming Station: Top & bottom flush/bevel/radius trimming, (2) 0.35 kW (0.5 HP) - 12,000 RPM motors, tiltable 0° - 20°, pneumatic exclusion from operator panel. -- Profile Scraping Unit: For thick PVC/ABS radius scraping, pneumatic in/out positioning from control panel with chip collection box. -- Flat Glue Scraper: To remove potential glue squeeze out. -- Buffing Unit: Top/Bottom, (2) 0.12 kW (1/8 HP) - 1,650 RPM motors, tilting horizontally and vertically. -- Controller: "Unitronics V350" Controller with color touchscreen, memory up to (20) programs. -- Equipped with: Feed Speed: 9 & 14 MPM (29 & 46 FPM). -- Power hold-down beam, workpiece support outrigger, safety & sound enclosure. -- Included Options:RIEPE non-stick Spray System. -- Actual Model is: CEHISA PRO 10

CEHISA PRO-12 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Features: Pre-Milling Station with:2 x 1.5 Kw (2.0 HP) 12,000 RPM motors, standard equipped with diamond cutters. Both spindles pneumatically controlled. -- Spray agent unit for top and bottom with (2) sprayer and (2) reservoir -- Automatic Edge Magazine: For coiled material up to 3 mm thickness, strip feed magazine for up to 5 mm (3/16") solid wood banding. -- Quick Melt Glue System, MR-5:10 - 15 min. heat-up time, auto temperature drop. Glue Tank is coated with nonstick material, quick-change mechanism for easy maintenance and/or color change. -- Pressure Section:(1) Large dia. driven and (2) idle rollers. Digital read-out and pneumatic positioning selectable from controller touch screen.Edgebanding Workstations: -- End Trimming Station, V-7: Double motor front & rear, 2 x 0.35 Kw (0.5 HP) - 12,000 RPM. -- Edge Trimming Station, BC-5: Top & bottom flush/bevel/radius trimming, 2 x 0.55 Kw (0.75 HP) - 12,000 RPM, tiltable 0° - 10°, pneumatic exclusion from operator panel. -- Corner Rounding Unit, FD-50: To process overhanging edges and trimming around the leading & trailing edge, 1 x 0.27 Kw (0.36 HP). -- Profile Scraping Unit, R-8: For thick PVC/ABS radius scraping, pneumatic in/out positioning from control panel with chip collection box. -- Flat Glue Scraper, RR-7: To remove potential glue squeeze-out. -- Buffing Unit, PC-9: with spry mist unit top/bottom Top/Bottom, 2 x 0.12 Kw (1/8 HP) - 1,650 RPM motors, tilting horizontally and vertically. -- Operator Interface:PLC Microprocessor control with color touch screen, memory up to 20 programs.Equipped With:Feed Speed, 9 - 14 MPM (29' to 45 FPM), -- Power hold-down beam, work-piece support outrigger, safety & sound enclosure. Included Options:Riepe, non-stick spray system. -- Nesting Tracer Shoes for top/bottom trimmers

CEHISA - PRO-9, ...Edgebander Single-Phase Electrical!Single-sided Edgebander with: End trim; top/bottom trimming; scraping; buffing.Specifications: -- 0.4 - 3 mm Edge thickness cap., -- Teflon coated glue pot system. -- Automatic magazine for strip & coil feed; Heavy-Duty guillotine for up to 3 mm thick PVC. -- (2) roll pressure zone with (1) motorized and (1) idle roller. Workstations: -- Double-motor end trim station; 0.33 HP - 12,000 RPM ea. motor. -- Top & bottom flush/bevel trim; bevels 0° - 20°; 0.45 HP ea. motor. -- Top & bottom PVC profile scraper; up to 3 mm radius. -- Last Station: Top & bottom buffing unit; 3/4 HP motors. -- Electronic braking on trim motors; digital readout on top/bottom trim. -- Feed speed: 33 FPM & 1 HP feed drive. -- Sound enclosure. -- Outboard panel support. -- Frequency converter. -- Digital readouts for trimmer adjustments. -- Sound enclosure.

CEMCO - UF-1137SE, ...Single Head Wide Belt Sander37" Width cap.; combination sanding head.Head Configuration:5-1/2" Rubber covered contact roller andIndependently adjustable 3-1/2" polishing platen.20 HP Main motor.36" x 75" Abrasive belt size; electric eye tracking.1 HP Variable speed feed, 15 - 60 FPM.Equipped with & Features:0" - 6" Manual part thickness opening of conveyor bed with:(4) 5-Ton lifting jacks.Double infeed & outfeed rubber covered holddown rollers.26" Infeed & 20" outfeed.Air disc brakes on sanding head.Load meter & push button magnetic starter.

CEMCO - URF-3352, ...3-Head Wide Belt Sander.53" Width cap. Drum, Drum Combination Head.Head Configuration:1st Head: Rubber-covered contact roll, 10" dia., 65 shores (to be verified), adjustable with a dial indicator, 50 HP motor.2nd Head: Rubber-covered contact roll, 10" dia., 65 shores (to be verified), adjustable with a dial indicator, 40 HP motor.3rd Head: Combination Head, (2) 5-1/2" finishing Drums & Platen.4th Station: Panel Brush.Specifications: -- 6" Max. working thickness. -- 1 HP Variable speed feed. -- 53" x 75" Abrasive belt size. -- Power raise & lower of feed bed. -- Numerical digital readout of thickness. -- Spring-loaded holddown rollers through machine. -- 36" Infeed table, 30" outfeed table; feed speeds from 5 - 60 FPM, 3 HP inverter. -- Load meters. -- (2) 8" Dia. dust outlets. Equipped with & Features: -- Belt Tracking (Electric Eye). -- Constant Pass-Line machine.Some spec's need to be verified.