CAM-WOOD A-2560 Single Head, Wide Belt Sander;Features & Specifications: -- 24" Width cap. - sanding head with a rubber covered contact roll and adjustable finishing platen, 10 HP motor. -- 25" x 60" Abrasive belts, pneumatic abrasive belt tensioning. -- 0" - 5" Feed through bed adjustment, 0.5 HP motor power elevation for thickness opening. -- Variable conveyor feed speed from 17 - 51 FPM, 1 HP feed motor. -- 5" Max. working thickness, 7" min. working length, -- Double Infeed & outfeed spring loaded holddown rolls.Complete with: -- Magnetic controls, 6" dia. dust collection hood, and safety shutoff. - 1,500 CFM Dust collection required. Optional: 10 HP Single Phase motor

CAM-WOOD A-3760X Combination Head Wide Belt SanderSpecifications: -- 36" Width cap. - Combination Sanding head with rubber-covered contact roll and adjustable finishing platen. 20 HP main drive motor. -- 37" X 60" Abrasive belts, pneumatic abrasive belt tensioning. -- 0" - 5" Feed through bed adjustment, Digital thickness set-up via 0.5 HP motor power elevation for thickness opening. -- Variable conveyor feed speed from 20 to 60 FPM, 2 HP feed motor. -- 5" Max. working thickness, 7" min. working length, -- Double Infeed & outfeed spring loaded holddown rolls.Complete with: -- Magnetic controls, 6" dia. dust collection hood, and safety shutoff. - 1,500 CFM Dust collection required.

CAM-WOOD A-3775 Single Head Wide Belt SanderSpecifications: -- 36" Width cap. - Combination Sanding head with rubber-covered contact roll and adjustable finishing platen. 20 HP main drive motor. -- 37" X 75" Abrasive belts, pneumatic abrasive belt tensioning. -- 0" - 5" Feed through bed adjustment, Digital thickness set-up via 0.5 HP motor power elevation for thickness opening. -- Variable conveyor feed speed from 20 to 60 FPM, 2 HP feed motor. -- 5" Max. working thickness, 7" min. working length, -- Double Infeed & outfeed spring loaded holddown rolls.Complete with: -- Magnetic controls, 6" dia. dust collection hood, and safety shutoff. - 1,500 CFM Dust collection required.

CAM-WOOD AC-100120 Piston Air CompressorHeavy Duty unit with a 10 HP induction motor.Features & Specifications: -- 34.2 CFM @ 90 PSI, Splash lubricated cast iron 2-stage pump. -- Automatic start/stop operation. -- 120-Gal. horizontal tank that meets the ASME standards. -- Manual tank drain & pressure gauge. -- Deep finned after-cooler. -- Fully enclosed belt guard and ON/OFF pressure switch. -- Deep finned cylinder head for cooling and replaceable air filter/silencer. -- Durable painted finish for years of service under the worst conditions.

CAM-WOOD AC-5080 Piston Air CompressorCompact unit with a 5 HP induction motor.Features & Specifications: -- 18 CFM @ 90 PSI, Splash lubricated cast iron 2-stage pump. -- Automatic start/stop operation. -- 80-Gal. vertical tank that meets the ASME standards. -- Manual tank drain & pressure gauge. -- Deep finned after-cooler. -- Fully enclosed belt guard and ON/OFF pressure switch. -- Deep finned cylinder head for cooling and replaceable air filter/silencer. -- Durable painted finish for years of service under the worst conditions.

CAM-WOOD AC-7580 Piston Air CompressorCompact unit with a 7.5 HP induction motor.Features & Specifications: -- 22 CFM @ 90 PSI, Splash lubricated cast iron 2-stage pump. -- Automatic start/stop operation. -- 80-Gal. vertical tank that meets ASME standards. -- Manual tank drain & pressure gauge. -- Deep finned after-cooler. -- Fully enclosed belt guard and ON/OFF pressure switch. -- Deep finned cylinder head for cooling and replaceable air filter/silencer. -- Durable painted finish for years of service under the worst conditions.

CANTEK SRS330 Straight Line Rip Saw;Features: -- Very Rigid machine body with a welded steel frame with an integral cast & machined table, which is fitted with a sturdy cast column & saw unit. -- Excellent precision work accuracy and durability. -- Absolute straight line feeding up to 13 ft. of ripping. -- Precision caterpillar chain and double "VEE" extra long (47.2";) guide rails are made of special cast iron the chain connecting pins are made of high grade steel - heat treated & ground for high durability and low wear. -- (8) Holddown rolls (6 rows).Specifications: -- Max. work piece thickness 4.33". -- Min.work piece length 8". -- Distance between saw and column 18.1". -- Saw arbor dia. 1" and Saw blade dia. 10"; - 14". -- Saw arbor speed 4,300 RPM. -- Useable Chain Length 47";. -- Glue line guarantee 13’ (+/- 0.0098"; or 0.25 mm). -- Feed speeds variable 30 to 130 FPM. -- Arbor motor 20 HP -- Feed motor 2 HP -- Table size 36.6" x 64.6, Table height 31-7/8". Utilities: -- 230 V = 60.8 Full Load Amps. -- Electrics 460/3/60 = 30.4 Full Load Amps. -- Dust Collection Outlet 4"; -- Net weight 3,190 Lbs.Available Options: -- 20mW Red Laser (FPIMLC1320WFL) & Laser Holder (FPICAN03) -- Extra Saw Blade: 14";x0.157"; kerf x 1.5"; bore x 60T (CANC14RS-BLADE-14)

CANTEK SS512CSB Heavy Duty Production Shaper with Sliding Table & Spindle Brake7.5 HP Features: -- Cast iron sliding table runs on ball bearing for smooth table transition. -- Cast iron ground & polished table with insert rings; table size: 31- ½"; x 39.4″. -- Precision ground and electronically balanced spindle. -- V-belt drive with (5) feed speeds is easily accessed from the front of the machine. -- Electric spindle brake for added safety. -- Spindle lock - with limit switch safety, machine will not start with lock engage. -- Micro spindle height adjustment with dial indicator. -- Interchangeable cutter spindle. -- Forward/reverse spindle rotation. -- Adjustable "finger" type fence Independent micro-fence adjustment on both sides. -- Includes the following standard equipment: 1- 1/4" Spindle, (1) 5"; dust chute on guard & (1) 4"; dust chute in the table, safety guard, Miter tenon jig, and Telemecanique magnetic controls.Net weight 1034 Lbs. Machine dimensions 48.4"; x 39.4"; x 52 ¾";. Shipping weight 1166 Lbs.Shipping dimensions 45 ¼"; x 37"; x 41";

CANTEK - SS512TB Tilting Spindle ShaperSpecifications: --Tilting spindle from -5° to +45° and 6" x 43" fence. --1-1/4" interchangeable spindle is standard (other sizes available). -- Large cast-iron table is ground and polished for maximum stability and durability. -- Powerful 7.5 HP motor for even the most demanding profiling work. -- Five spindle speeds can be easily adjusted to suit your tool diameter. -- 5-1/2" Useable spindle length, above table 13-¼"; below table 8-¼". -- Electronic spindle brake for added safety and facilitates fast changeover. -- Precision fence assembly with micro-infeed and outfeed fence adjustment. -- The finger-style fence allows the fence to be adjusted around the cutter for added safety and workpiece stability. -- Table size 31 ½"; x 39.4″. -- Dust port (1) 5″ on guard, (1) 4" into the table.

CANTEK SS-512TSB Tilting Spindle and Sliding Table Shaper:7.5 HP - 3-Phase motor, overall table dimensions 31.50" x 39.40", sliding table 10.25" x 39.40". -- Spindle stroke 7"; 1-1/4" dia. spindle with 5 MT receiver and 4-3/4" cap. under the nut. Spindle tilts -5° & +45°. -- (5) Spindle speeds: 3,000, 4,000, 6,000, 8,000 & 10,000 RPM.Complete with: Spindle reversing switch, micro-adjustable fence 6" x 43", thermal overload protection and dust hood.16 weeks delivery.

CANTEK 1214 TABLE SAWHeavy-duty cast iron table precision ground for accuracy. -- Rugged machine frame construction provides maximum stability and reduced vibration. -- 14" Blade capacity. and 0° - 45° tilting arbor. -- 10 HP Motor with double V-belt drive. -- Rip fence for a 50" max. cut with a precision Rip fence. -- 48" x 38" Cast iron table. -- Blade guard, miter gauge, push button controls. -- Parts list & operation manual.

CANTEK TA-14 Tilting Arbor Table Saw. -- Heavy-duty cast iron table precision ground for accuracy. -- Rugged machine frame construction provides maximum stability and reduced vibration. -- 14" Blade capacity. and 0° - 45° tilting arbor. -- 7.5 HP Motor with double V-belt drive. -- Rip fence for a 50" max. cut with a precision Rip fence. -- 48" x 38" Cast iron table. -- Blade guard, miter gauge, push button controls. -- Parts list & operation manual.

CANTEK HB-800 32" Vertical Band Resaw32" Wheel diameter, 20 HP motor Vertical Band Saw;Specifications: -- 3.543" (90 mm) wheel width, 30-5/8" throat capacity, 15-3/8" under guide capacity. -- 4" Blade width X 216- 217-1/8" blade length. -- 20 HP main motor, generates a blade speed of 5,024 SFPM.Features: -- Heavy fabricated steel machine frame. -- Specially designed Bakelite guide blocks provide rigid side blade support for straight cutting. -- Large cast iron work table is precision ground & can tilt to a maximum of 45°. -- Convenient blade tension adjustment by means of a handwheel and gauge. -- Cast iron upper and lower saw wheels are precision machined and dynamically balanced. -- Rack & pinion blade guide adjustment. -- Wheel is crowned for proper blade tracking & added stability of the blade.Complete with: -- Foot brake for braking wheels & blade. -- Blade lubrication system and reservoir for lubricant keeps blades cool.Including Electrics to UL/CSA - all starters -- Auto Start-Delta control for main motor with Emergency Stop Switch -- Telemecanique brand magnetic switchHF-150A Feeder: -- 1 HP motor with variable feed speed from 16 - 66 FPM; 6" feed opening. -- Pneumatic tensioned feed roller. -- Feed pressure is adjustable. -- Feed roller opening & closing is controlled by a foot switch for operator convenience. -- Knurled steel roller.

CANTEK - GT400BRD 16″ Double Surface PlanerGeneral description: -- Spring-loaded conveyor pin system ensures material is passed over the bottom cutterhead to resulting in a flat and uniform board prior to planning to thickness on the top head. -- Spiral insert knife cutterheads with two-sided solid carbide knives produce a smooth finish with increased stock removal capacity and extremely quiet operation. -- Heavy-duty cast-iron machine body and table for vibration-free cutting.Digital electronic thickness adjustment in INCH and MM (Inch = 0.001"; / mm = 0.01mm resolution) for precise thickness control KEY ADVANTAGES SERVICESpecifications: -- 16″ Wide x 6.7″ thick planing capacity -- 10 HP Bottom Head and 15 HP Top Head -- Cutterheads are spiral insert types with six (6) rows of carbide inserts. Cutterhead speed 5,400 RPM. (2) Driven and (1) idle bed roll for superior feeding of even difficult material. -- Swiveling control panel for more ergonomic access to machine controls -- Inverter variable speed control with feed speeds from 26 to 80 FPM, 2 HP variable feed drive.Features: -- Easy to access external handwheel adjustment of infeed bed -- Hard chromed worktable for high wear resistance -- Auto lubrication to conveyor chain, central lubrication for dovetail elevation guideways -- Section chipbreaker and sectional feed roller before top cutterhead -- Rubber outfeed top roller to prevent chip marking -- Over thickness safety shut-off bar across infeed. -- Ammeter for each motor on control panel to monitor motor load -- Star-Delta soft start.

CANTEK GT-635 ARD Top & Bottom Head Surfacer Specifications: -- 25" X 8" Cap., Min. thickness 3/8", 11.2" Min. length. -- Powered by 25 HP - 1,765 RPM Top & 20 HP Bottom head motors, Belt-driven helical spiral insert cutterheads at 6,000 RPM, Each head with (6) Rows of 4-Sided Carbide inserts, 30 x 12 x 1.5 mm (1.18" x 0.47" x 0.6") Insert knife dimensions, Capable of taking of up to 1/4" in (1) pass on each head. -- Variable feed speeds 23 - 52 FPM powered by 3 HP Motor, Hard chrome-plated & precision ground table for maximum wear resistance. -- (2) Sets of 4" Dia. Upper pneumatic-tensioned rollers, (1) 4" Dia. Powered top outfeed roller, (3) 4" Dia. Non-powered bed rollers & Caterpillar spring-loaded feed chain system with Auto-adjustment device to prevent damage due to improper tension & Automatic lubrication.. -- Power raise & lower of table guided by (4) Gib-guided post screws via 1/2 HP - 1,680 RPM Motor. The transmission system is directly driven by flexible shafts for high accuracy, "GTM-525" LED Touchpad Control for fine adjustment of thickness control.Complete with: -- Control panel, with Push button controls & LED Readouts for height & speed adjustments. -- Overheight safety bar & Emergency stop button on feed control. -- Cradle for removable bottom cutterhead.NOTE: Machine 220/440 V, Wired for 220 V.

CANTEK - GT635ARD-16 25″ Double Surface Planer25″ Wide x 16″ thickness capacity Add on $2,500 for increase HP of top head to 30 HPFeatures: -- Cutterheads are spiral insert types with six (6) rows of carbide inserts. -- (2) Driven and (1) idle bedroll for superior feeding of even difficult material. -- Swiveling control panel for more ergonomic access to machine controls. -- Inverter variable speed control with feed speeds from 26 to 80 FPM. -- Easy to access external handwheel adjustment of infeed bed. -- Hard chromed worktable for high wear resistance. -- Auto lubrication to conveyor chain, central lubrication for dovetail elevation guideways. -- Sectional chip breaker and sectional feed roller before top cutterhead.. -- Rubber outfeed top roller to prevent chip marking. -- Over thickness safety shut-off bar across infeed. -- Ammeter for each motor on the control panel to monitor motor load.Specifications: Maximum working width 25″Maximum working thickness 16″; Minimum thickness 0.394"; Min. workpiece length 12.2″Bottom head motor 20 HP, Top planing head motor 25 HP - Feed motor 5 HPTable elevation motor 1/2 HP.Cutterhead diameter 4", Knife dimensions 30 mm x 12 mm x 1.5 mm w/bevels (96 pcs per head)Cutterhead speed 5400 RPM;Feed speed (variable) 26 - 80 FPMDust ports 2 @ 6";; Table dimensions 27" x 103" (41.85" from the floor);Machine voltage 460/3/60 = 70 amps.Dims & Weight (LxWxH) 105″ x 45.1″ x 92.9″; (max.) Net weight 6700 Lbs,Packaging dimensions 109″ x 49″ x 89″; Gross weight 7800 Lbs

CANTEK - GT635ARD-8 25″ Double Surface Planer25″ Wide x 8″ thickness capacity Add on $2,500 for increase HP of top head to 30 HPFeatures: -- Cutterheads are spiral insert types with six (6) rows of carbide inserts. -- (2) Driven and (1) idle bedroll for superior feeding of even difficult material. -- Swiveling control panel for more ergonomic access to machine controls. -- Inverter variable speed control with feed speeds from 26 to 80 FPM. -- Easy to access external hand wheel adjustment of infeed bed. -- Hard chromed worktable for high wear resistance. -- Auto lubrication to conveyor chain, central lubrication for dovetail elevation guideways. -- Sectional chip breaker and sectional feed roller before top cutterhead.. -- Rubber outfeed top roller to prevent chip marking. -- Over thickness safety shut-off bar across infeed. -- Ammeter for each motor on the control panel to monitor motor load.Specifications: Maximum working width 25″Maximum working thickness 8″; Minimum thickness 0.394"; Min. workpiece length 12.2″Bottom head motor 20 HP, Top planing head motor 25 HP - Feed motor 5 HPTable elevation motor 1/2 HP.Cutterhead diameter 4", Knife dimensions 30 mm x 12 mm x 1.5 mm w/bevels (96 pcs per head)Cutterhead speed 5400 RPM;Feed speed (variable) 26 - 80 FPMDust ports 2 @ 6";; Table dimensions 27" x 103" (41.85" from the floor);Machine voltage 460/3/60 = 70 amps.Dims & Weight (LxWxH) 105″ x 45.1″ x 92.9″; (max.) Net weight 6700 Lbs,Packaging dimensions 109″ x 49″ x 89″; Gross weight 7800 Lbs

CANTEK GT610HI CARDAN SHAFT DRIVE DOUBLE SURFACE PLANERSpecifications: -- Max. working width 24" (610 mm). -- Max. working thickness 8" (200 mm). -- Min. working thickness 5/16″ (8 mm). -- Min. working length 12" (300 mm). -- Cutterhead RPM 5000 RPMCutterhead diameter 5.3" (135 mm). -- Feed speed 30-98 FPM 10 – 30 m/min. -- Top cutterhead motor 40 HP. -- Bottom cutterhead motor 30 HP. -- Feed motor 5 HP. -- Table Rolls 7 (3) driven. -- Opening hoist motor 1 HP. Machine dimensions: (LxWxH) 112"; x 67"; x 67"; 2830x1700x1700mm . Machine weight 8800 Lbs 4000 kgsShipping weight 9240 lbs 4200 kgs. -- Shipping dimensions (LxWxH) 115"; x 75"; x 75"; 2900 x 1900 x 1900mmMachine electrics (Standard) 460/3/60 = 110 amps (Other voltages on request, factory order)Key Advantages• Cast iron machine frame for superior vibration damping resulting in a long machine & bearing life.• Chrome-plated tables and top and bottom for maximum wear resistance.• Cutterheads are mounted in precision ABEC 7 RHP bearings.• The feed system uses a spring-loaded pin arrangement to pass material over the bottom jointing head.• Sectional serrated infeed roll before the top cutterhead.• Variable feed speed by frequency inverter (VFD) with digital display for the feed speed.• Digital thickness control for quickly and precisely setting the desired thickness.• The upper assembly is adjusted for desired thickness by four large-diameter cylindrical posts.• Adjustable infeed bed by easily accessible handwheel to set desired stock removal on the bottom head.• Easy to access swivel control panel with individual ammeters for load monitoring and hour meter to aid in maintenance planning.• Cutterhead starters are Y-Delta providing a soft start to the heads for reduced power consumption on startup.• Automatic lubrication to the conveyor feed system.• High-quality Schneider electrical components to CSA/UL standard.

CANTEK JF-330A Profile Knife Grinder Clamping length of 12" (300 mm) for both straight and profile grind; dia. of knife swing 12" (300 mm). -- Grinding Arbor: 3 HP grinding motor with VFD (LED Readout) drive from 1.500 to 4.200 RPM. Quick change removable (140 mm) wheel adapter. Machine set for axial constant grinding and template set up on right-hand side.Over the wheel precision diamond dresser assembly for dressing and dimensioning of wheel. Manual positioning: of grinding wheel to tool; positioning of back clearance angle and side clearance angle 5°/10° and 15°. Quick change stylus turret for applications; (6) included with machine. -- Carriage: SCHNEEBERGER linear bearing table movement. Table movement 12" x 6". -- Coolant system: 1/8 HP motor from coolant pump located in the tank below; (3) coolant nozzles for smooth flow of coolant to knife rest during grinding. Additional hose with nozzle for cleanup. Stainless steel splash guards throughout! -- Includes: Set up tools, coolant, HD worklight, grinding wheels and (1) arbor of choice - (1.25", 1.5", 40mm, 1-13/16", 2.125" or 50 mm).

CANTEK EM-12 End Matcher;1.6" to 12" Width x 0.4" to 1.38" thickness (to 2-1/4" optional) x 10.6" min. length capacity. Unlimited lengths possible.Specifications: -- Feed speeds to 295 FPM with approximate production speeds of 77 FPM (based on 6-1/2' incoming boards). -- Standard 173" long infeed table and standard 86" (2,200 mm) long outfeed table; -- (2) 10 HP cutterhead motors with 40 mm spindle diameters; 1 HP feed motor; 1/2 HP motor drive to cutterhead carriage; clamping pressure from top and side; 24 volt DC controls.Standard equipment and Features: -- Designed for machining tongue & groove with or without V's on flooring and panel products; designed to be used for finger joint cutting. -- Heavy-duty self supporting main frame; compact design requires minimum floor space.Feedworks: -- Capable of processing material as short as 11" to an unlimited length; variable speed through-feed systems is controlled by frequency inverter; through-feed system allows the tongue to be cut simultaneously on the tail of one board and the leading edge of the next board. -- Powered top Urethane rolls and spring loaded bed rollers feed the material into position for processing. -- Pneumatic side pressure ensures the material is held square against the fence.Complete with: -- Safety and noise reduction enclosure; convenient touch screen control is used to quickly activate and adjust the machine functions. -- Powered 176" long infeed conveyor is included (additional length optional); with a 86.6" long outfeed table (additional length optional). -- Includes: (2) Individual Precision Insert Tooling Heads as Supplied with Machine & stacked to make (1) pair of heads; set of heads provided for groove on left and tongue on right.